Runco Vision 85 manual Video 1 / S-VIDEO, Volt 750 mA Trigger Outputs, ComLink RS-232 Output

Page 22

Controls and Functions

5.COMPOSITE VIDEO INPUT

Standard composite video input for connecting a VCR, laser disc player or other composite video source.

6.S-VIDEO 1 / S-VIDEO 2

Two, standard S-Video inputs for connecting a DVD player, satellite receiver or Super VHS (S-VHS) VCR.

7.12-VOLT (750 mA) TRIGGER OUTPUTS

Connection for up to three (3), 12-volt trigger-controlled devices such as retractable screens or screen masks.

8. ComLink (RS-232) OUTPUT

Connect this to the ComLink (RS-232) input on the projector, using the provided communication cable.

9.IR

Wired input from a wired remote control or infrared receiver. It is a 3.5-mm, mini phono jack, wired as follows:

Ring = +5V Tip = IR Input Sleeve = Ground

When an external remote control or infrared receiver is connected to the

Note	wired IR input, the IR sensor on the front of the VHD is disabled.

10.RS-232 CONTROL PORT

A female, 9-pin D-sub connector for interfacing with a PC or home theater automation/control system.

11.POWER INPUT (100 to 240 VAC)

Connect the VHD Controller to power here.

12.MAIN AC FUSE

This is the main AC input fuse (5mm x 20mm, 500 mA, 250V slow-blow).

13.MAIN POWER SWITCH

Disconnects or applies power to the VHD Controller.

10	Vidikron Vision 85 Owner’s Operating Manual

Image 22

Contents 1080p DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Table of Contents OperationSpecifications Maintenance and TroubleshootingSerial Communications Table of Contents 1List of Figures VHD Controller OSD Menu Structure for VisionList of Figures Xii About This Manual 1IntroductionThis Manual Performance or cause a malfunction Using This ManualThey also provide supplemental information If you need Turn toDescription, Features and Benefits Optional Accessories Controls and Functions Vision 85 at a GlanceVertical Lens Shift RS-232C Input RJ-11 female connector Wired IR 3.5-mm, mini phono jack Vision 85 Rear Panel VHD Controller Front Panel VHD Controller Front PanelHdmi 1 / Hdmi 2 Digital Component Video RCA connectorsVHD Controller Rear Panel InputsVolt 750 mA Trigger Outputs Power Input 100 to 240 VACVideo 1 / S-VIDEO ComLink RS-232 OutputVision 85 Remote Control Unit VHD Controller/Vision 85 Remote ControlENT Enter On / OFFCursor Buttons Video Memory Preset Buttons ISF NT NightCust VID 1 2 / S-VID 2 5 S-VideoVision 85 Built-In Keypad Not usedTo install batteries in the remote control 3InstallationRemote Control OperationInstallation Step Procedure For Details, Refer to Quick SetupInstallation Overview SignalsInstallation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsThrow Distance Floor Installation Ceiling InstallationPosition Folded Optics Floor Mounting Upright Adjusting the ProjectionMounting the Vision Ceiling Mounting InvertedConnections to the Vision 85 and VHD Controller Connector Panel AccessVHD Controller Hdmi Connections See Figure Connecting SourceController Hdmi Source HD-DVD/BD/DVD Player or HD Tuner withDigital DTV RGB or Component Video Connections See Figure Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcOutputs to External Connecting a PC orEquipment Connecting an External IR Receiver to the VHD Controller 13 -volt Trigger Output Connection from ProjectorTurning on the Power Adjusting the Picture OrientationPrimary Lens Adjustments 15. Vertical and Horizontal Lens Shift AdjustmentsInstalling and Adjusting the CineWide Anamorphic Lens Adjusting the Lens Height Y Anamorphic Lens Top View Using the On-Screen Menus 4OperationInput Source ISF PresetsService Aspect RatioInput Source Main MenuAspect Ratio Aspect Ratio Settings Aspect Ratio DescriptionPicture Surface, eliminating the black bars.Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input PositionISF Presets InformationYou must enter a passcode to access the Calibration menu CalibrationGain/Offset Refer to ISF Night Display Color, above Press Menu to exit test pattern mode ServiceCode Standard Vision HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUVOperation On-Screen Menus for 1080i Digital or 1080p Signals Vision 85 Main Menu 1080i Digital or 1080p Sources Only Language Picture AdjustColor Temp VAC Iris Lamp Power KeyISF Night Effects of Primary Color Hue Adjustments Picture Adjust AdvancedWhite Balance Lamp Hours read-onlyRefer to Lamp Hours on HD/RGB AdjOptions Always set this option to On. Doing otherwise may disrupt Orientation Refer to Adjusting the Picture Orientation on Language settingOperation 5Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution To Table Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration 6Serial CommunicationsCommand Value Description Min/max Stored?Brightness Command Parameter Value Description Min/max Stored? Bkgnd Value Stored? Description Enter key7Specifications Vision 85 SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsVHD Controller Specifications Vision 85 Dimensions Vision 85 DimensionsPage Vidikron