Runco Vision 85 manual Position, Ceiling Installation, Floor Installation

Page 32

Installation

Vertical and Horizontal	➤	Proper placement of the projector relative to the screen will yield a rectangular,
Position		perfectly-centered image that completely fills the screen.
		Ideally, the projector should be positioned perpendicular to the screen and in such a way
		that the lens center and screen center are aligned with each other, as shown in Figure 3-3.

Ceiling Installation

Ceiling

Height

Projection Distance

Lens Center

x

	Screen	Lens Center
Floor Installation
Height	Screen	Lens Center
Lens Center
x
	Projection Distance
		Floor
Figure 3-3. Projector Placement

Vertical Lens Shift ➤ If it is not possible to align the projector and screen as shown in Figure 3-3,you can use the lens shift controls to center the image on the screen. Lens shift is generally expressed as a percentage of the screen height or width, as shown in Figure 3-4.

Screen Center

0%

50% Height

Lens Shift

(0.5 x H)

100% Height

Lens Shift

(1.0 x H)

Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens or

projector is used in this example.

Figure 3-4. Vertical Lens Shift (EXAMPLE ONLY)

20	Vidikron Vision 85 Owner’s Operating Manual

Image 32

Contents 1080p DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Table of Contents OperationSerial Communications Maintenance and TroubleshootingSpecifications Table of Contents 1List of Figures VHD Controller OSD Menu Structure for VisionList of Figures Xii This Manual 1IntroductionAbout This Manual Using This Manual They also provide supplemental informationPerformance or cause a malfunction If you need Turn toDescription, Features and Benefits Optional Accessories Controls and Functions Vision 85 at a GlanceVertical Lens Shift Vision 85 Rear Panel Wired IR 3.5-mm, mini phono jackRS-232C Input RJ-11 female connector VHD Controller Front Panel VHD Controller Front PanelComponent Video RCA connectors VHD Controller Rear PanelHdmi 1 / Hdmi 2 Digital InputsPower Input 100 to 240 VAC Video 1 / S-VIDEOVolt 750 mA Trigger Outputs ComLink RS-232 OutputVision 85 Remote Control Unit VHD Controller/Vision 85 Remote ControlCursor Buttons On / OFFENT Enter Memory Preset Buttons ISF NT Night CustVideo VID 1 2 / S-VID 2 5 S-VideoVision 85 Built-In Keypad Not used3Installation Remote ControlTo install batteries in the remote control OperationInstallation Quick Setup Installation OverviewStep Procedure For Details, Refer to SignalsInstallation Considerations Projector Installation OptionsInstallation Type Advantages ConsiderationsThrow Distance Position Ceiling InstallationFloor Installation Folded Optics Adjusting the Projection Mounting the VisionFloor Mounting Upright Ceiling Mounting InvertedVHD Controller Connector Panel AccessConnections to the Vision 85 and VHD Controller Connecting Source ControllerHdmi Connections See Figure Hdmi Source HD-DVD/BD/DVD Player or HD Tuner withDigital DTV RGB or Component Video Connections See Figure Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcEquipment Connecting a PC orOutputs to External Connecting an External IR Receiver to the VHD Controller 13 -volt Trigger Output Connection from ProjectorTurning on the Power Adjusting the Picture OrientationPrimary Lens Adjustments 15. Vertical and Horizontal Lens Shift AdjustmentsInstalling and Adjusting the CineWide Anamorphic Lens Adjusting the Lens Height Y Anamorphic Lens Top View Using the On-Screen Menus 4OperationISF Presets ServiceInput Source Aspect RatioAspect Ratio Main MenuInput Source Aspect Ratio Settings Aspect Ratio DescriptionPicture Surface, eliminating the black bars.Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input PositionISF Presets InformationYou must enter a passcode to access the Calibration menu CalibrationGain/Offset Refer to ISF Night Display Color, above Press Menu to exit test pattern mode ServiceCode Standard Vision HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUVOperation On-Screen Menus for 1080i Digital or 1080p Signals Vision 85 Main Menu 1080i Digital or 1080p Sources Only Picture Adjust Color Temp VAC Iris Lamp PowerLanguage KeyISF Night Effects of Primary Color Hue Adjustments Picture Adjust AdvancedWhite Balance Options HD/RGB AdjLamp Hours read-onlyRefer to Lamp Hours on Always set this option to On. Doing otherwise may disrupt Orientation Refer to Adjusting the Picture Orientation on Language settingOperation 5Maintenance and Troubleshooting Lamp ReplacementSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart To Table Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands 6Serial CommunicationsCommand Value Description Min/max Stored?Brightness Command Parameter Value Description Min/max Stored? Bkgnd Value Stored? Description Enter key7Specifications Vision 85 SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsVHD Controller Specifications Vision 85 Dimensions Vision 85 DimensionsPage Vidikron