Runco Vision 85 manual Operation

Page 62

Operation

Miscellaneous: Select Miscellaneous from the Service menu to set the following options:

Language: Select Language from the Miscellaneous menu and press the up- or down-arrows to select the OSD Language. (Currently, only English is supported.)

Menu Mode: This is the manner in which the OSD menus appear and disappear when you press MENU. Choose one of the following:

0 = No transition; menus abruptly appear and disappear.

1 = Menus fade in and out.

2 = “Checkerboard” dissolve; menus appear and disappear in sections.

3 = “Window shade” effect; menus are drawn on a diagonal from top left to bottom right, and retract in the opposite direction.

Timeout - Short/Long: These settings control how long the OSD menus stay on screen. Select a time-out period of from 2 to 60 seconds.

Side Bar Color: This controls the color of the inactive image area. The range is from -100 (black) to 100 (white).

The inactive image area is on either side of the active image area when using the 4:3 aspect ratio (or the entire screen when no incoming video signal is present).

Film Mode: Enable Film Mode to smooth out moving images from interlaced, standard-definition (SD) sources. In most cases, the Vision 85 detects the proper “pull-down” rate and vertical frequency. However, if your source is jittery and/or tearing you may wish to enable Film Mode to ensure stable processing for that source.

System Reset: To reset ALL controller settings (including image settings) back to their factory defaults, choose System Reset from the Service menu.

A confirmation message appears, reminding you to save your settings before you perform the reset, so that you can restore them afterwards. If you have done this, select Confirm to continue with the reset. Otherwise, click Back to cancel.

This action is not undoable. Proceed with caution! Before you perform a Caution System Reset, save ALL settings, including “Custom” ISF Presets (page 44), ISF

Day/Night presets (page 46), Output Shift settings (page 46), Input Names (page 47) and Trigger settings (page 49).

Restore Saved Settings: Following a System Reset, select Restore Saved Settings to apply all previously-saved settings to the projector and VHD Controller.

50

Vidikron Vision 85 Owner’s Operating Manual

Image 62
Contents 1080p DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Table of Contents OperationSerial Communications Maintenance and TroubleshootingSpecifications Table of Contents 1List of Figures VHD Controller OSD Menu Structure for VisionList of Figures Xii This Manual 1IntroductionAbout This Manual Performance or cause a malfunction Using This ManualThey also provide supplemental information If you need Turn toDescription, Features and Benefits Optional Accessories Controls and Functions Vision 85 at a GlanceVertical Lens Shift Vision 85 Rear Panel Wired IR 3.5-mm, mini phono jackRS-232C Input RJ-11 female connector VHD Controller Front Panel VHD Controller Front PanelHdmi 1 / Hdmi 2 Digital Component Video RCA connectorsVHD Controller Rear Panel InputsVolt 750 mA Trigger Outputs Power Input 100 to 240 VACVideo 1 / S-VIDEO ComLink RS-232 OutputVision 85 Remote Control Unit VHD Controller/Vision 85 Remote ControlCursor Buttons On / OFFENT Enter Video Memory Preset Buttons ISF NT NightCust VID 1 2 / S-VID 2 5 S-VideoVision 85 Built-In Keypad Not usedTo install batteries in the remote control 3InstallationRemote Control OperationInstallation Step Procedure For Details, Refer to Quick SetupInstallation Overview SignalsInstallation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsThrow Distance Position Ceiling InstallationFloor Installation Folded Optics Floor Mounting Upright Adjusting the ProjectionMounting the Vision Ceiling Mounting InvertedVHD Controller Connector Panel AccessConnections to the Vision 85 and VHD Controller Hdmi Connections See Figure Connecting SourceController Hdmi Source HD-DVD/BD/DVD Player or HD Tuner withDigital DTV RGB or Component Video Connections See Figure Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcEquipment Connecting a PC orOutputs to External Connecting an External IR Receiver to the VHD Controller 13 -volt Trigger Output Connection from ProjectorTurning on the Power Adjusting the Picture OrientationPrimary Lens Adjustments 15. Vertical and Horizontal Lens Shift AdjustmentsInstalling and Adjusting the CineWide Anamorphic Lens Adjusting the Lens Height Y Anamorphic Lens Top View Using the On-Screen Menus 4OperationInput Source ISF PresetsService Aspect RatioAspect Ratio Main MenuInput Source Aspect Ratio Settings Aspect Ratio DescriptionPicture Surface, eliminating the black bars.Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input PositionISF Presets InformationYou must enter a passcode to access the Calibration menu CalibrationGain/Offset Refer to ISF Night Display Color, above Press Menu to exit test pattern mode ServiceCode Standard Vision HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUVOperation On-Screen Menus for 1080i Digital or 1080p Signals Vision 85 Main Menu 1080i Digital or 1080p Sources Only Language Picture AdjustColor Temp VAC Iris Lamp Power KeyISF Night Effects of Primary Color Hue Adjustments Picture Adjust AdvancedWhite Balance Options HD/RGB AdjLamp Hours read-onlyRefer to Lamp Hours on Always set this option to On. Doing otherwise may disrupt Orientation Refer to Adjusting the Picture Orientation on Language settingOperation 5Maintenance and Troubleshooting Lamp ReplacementSymptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart To Table Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration 6Serial CommunicationsCommand Value Description Min/max Stored?Brightness Command Parameter Value Description Min/max Stored? Bkgnd Value Stored? Description Enter key7Specifications Vision 85 SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsVHD Controller Specifications Vision 85 Dimensions Vision 85 DimensionsPage Vidikron