Runco Vision 85 manual Standard Vision, HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV

Page 61

Operation

Display Device: The options in the Display Device menu allow you to change the picture orientation, adjust the amount of overscan and access other projector-specific functions.

•Configure: Select Configure from the Display Device menu. Then:

•Orientation: Select Orientation to change the picture orientation to suit the method of installation (Floor Front, Floor Rear, Ceiling Front or Ceiling Rear).

•Overscan: Refer to Overscan on page 43.

•Fan Mode: If the projector is being used in a high-altitude environment, use the Fan Mode control to prevent it from overheating. Set it to High Altitude (“1”) to run the fan at high speed; set it to Normal (“0”) to run the fan at normal speed.

•Height: Select Height from the Display Device menu to adjust the displayed image height in small increments. Higher values compress the height. This setting affects all sources.

Use this control to fine-tune the image geometry on a Vision Note 85/CineWide. (It should not be necessary to change this setting on a

standard Vision 85.)

•Lamp Hours: To display the number of hours that the lamp has been in service, press or to highlight Lamp Hours.

HD Format: If the characteristics of the incoming signal on the HD1 or HD2 inputs are known, select HD Format from the Service menu and set them as described below. Doing so can reduce the time it takes the VHD Controller to switch from HD to 480i signals or vice versa.

This is generally not necessary unless the VHD Controller – for whatever reason – has difficulty determining the color space (RGB or YUV), bandwidth or resolution of the incoming HD signal. In most situations, the Auto settings work well.

•HD/RGB 1 and HD/RGB 2 (Color Space): Select Auto, RGB or YUV.

•ADC Bandwidth: Select Auto, 75 MHz, 150 MHz or 300 MHz.

•YPbPr Input Resolution: Select Auto or specify the input resolution, if known: 480i, 480p, 576i, 576p, 720p or 1080i.

Triggers: Select Triggers from the Service menu to configure the 12-volt trigger outputs. You can assign one or more trigger outputs to each aspect ratio. Those triggers are then activated by selecting that aspect ratio.

To save the trigger settings so that they can be restored after a System Reset (described below), press repeatedly to highlight “Save.” Then, press ENTER.

HD Format

HD/RGB 1

Auto

HD/RGB 2

Auto

ADC Bandwidth

Auto

YPbPr Input Resolution

 

Vidikron Vision 85 Owner’s Operating Manual

49

Page 60 Page 62
Image 61
Page 60 Page 62
Contents 1080p DLP Projectors Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation Table of ContentsSpecifications Maintenance and TroubleshootingSerial Communications Table of Contents VHD Controller OSD Menu Structure for Vision 1List of FiguresList of Figures Xii About This Manual 1IntroductionThis Manual They also provide supplemental information Using This ManualPerformance or cause a malfunction If you need Turn toDescription, Features and Benefits Optional Accessories Vision 85 at a Glance Controls and FunctionsVertical Lens Shift RS-232C Input RJ-11 female connector Wired IR 3.5-mm, mini phono jackVision 85 Rear Panel VHD Controller Front Panel VHD Controller Front PanelVHD Controller Rear Panel Component Video RCA connectorsHdmi 1 / Hdmi 2 Digital InputsVideo 1 / S-VIDEO Power Input 100 to 240 VACVolt 750 mA Trigger Outputs ComLink RS-232 OutputVHD Controller/Vision 85 Remote Control Vision 85 Remote Control UnitENT Enter On / OFFCursor Buttons Cust Memory Preset Buttons ISF NT NightVideo VID 1 2 / S-VID 2 5 S-VideoNot used Vision 85 Built-In KeypadRemote Control 3InstallationTo install batteries in the remote control OperationInstallation Installation Overview Quick SetupStep Procedure For Details, Refer to SignalsProjector Installation Options Installation ConsiderationsInstallation Type Advantages ConsiderationsThrow Distance Floor Installation Ceiling InstallationPosition Folded Optics Mounting the Vision Adjusting the ProjectionFloor Mounting Upright Ceiling Mounting InvertedConnections to the Vision 85 and VHD Controller Connector Panel AccessVHD Controller Controller Connecting SourceHdmi Connections See Figure Hdmi Source HD-DVD/BD/DVD Player or HD Tuner withDigital DTV RGB or Component Video Connections Digital DTV RGB or Component Video Connections See FigurePersonal Computer Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Composite/S-Video/Component Video Connections See FigureOutputs to External Connecting a PC orEquipment 13 -volt Trigger Output Connection from Projector Connecting an External IR Receiver to the VHD ControllerAdjusting the Picture Orientation Turning on the Power15. Vertical and Horizontal Lens Shift Adjustments Primary Lens AdjustmentsInstalling and Adjusting the CineWide Anamorphic Lens Adjusting the Lens Height Y Anamorphic Lens Top View 4Operation Using the On-Screen MenusService ISF PresetsInput Source Aspect RatioInput Source Main MenuAspect Ratio Aspect Ratio Description Aspect Ratio SettingsSurface, eliminating the black bars. PictureTypical Pluge Pattern for Adjusting Brightness Perform the adjustments in the order listed hereGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Typical Test Pattern for Adjusting SharpnessInformation ISF PresetsCalibration You must enter a passcode to access the Calibration menuGain/Offset Refer to ISF Night Display Color, above Service Press Menu to exit test pattern modeCode HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Standard VisionOperation On-Screen Menus for 1080i Digital or 1080p Signals Vision 85 Main Menu 1080i Digital or 1080p Sources Only Color Temp VAC Iris Lamp Power Picture AdjustLanguage KeyISF Night Picture Adjust Advanced Effects of Primary Color Hue AdjustmentsWhite Balance Lamp Hours read-onlyRefer to Lamp Hours on HD/RGB AdjOptions Always set this option to On. Doing otherwise may disrupt Language setting Orientation Refer to Adjusting the Picture Orientation onOperation Lamp Replacement 5Maintenance and TroubleshootingTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution To Table Maintenance and Troubleshooting RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands 6Serial CommunicationsValue Description Min/max Stored? CommandBrightness Command Parameter Value Description Min/max Stored? Bkgnd Enter key Value Stored? DescriptionVision 85 Specifications 7SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements DimensionsVHD Controller Specifications Vision 85 Dimensions Vision 85 DimensionsPage Vidikron
Top Page Image Contents