Runco Vision 85 manual Adjusting the Lens Height Y

Page 45

Installation

To avoid clipping the corners of the image, position the anamorphic lens

Tip	as close as possible to the primary lens.

Adjusting the Lens Height (Y):

1.Project a white field on the screen.

2.Ensure that the four Height (Y) Adjustment Screws are loose enough to allow vertical movement of the lens assembly.

3.Slowly move the anamorphic lens into place so that there are no shadows on the top or bottom of the screen:

Too Low

Correct position

Too High

4.When the height is properly set, tighten the Height Adjustment Screws to secure the lens in place.

Adjusting the Pitch (Angle): Next, angle the lens to even out any top-to-bottom pincushion distortion. To do this, loosen the Pitch Adjustment Screws on either side of the lens to allow it to pivot freely. Then, adjust the anamorphic lens angle so that the projected image is rectangular:

Vidikron Vision 85 Owner’s Operating Manual

33

Image 45

Contents 1080p DLP Projectors Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation Table of ContentsMaintenance and Troubleshooting SpecificationsSerial Communications Table of Contents VHD Controller OSD Menu Structure for Vision 1List of FiguresList of Figures Xii 1Introduction About This ManualThis Manual They also provide supplemental information Using This ManualPerformance or cause a malfunction If you need Turn toDescription, Features and Benefits Optional Accessories Vision 85 at a Glance Controls and FunctionsVertical Lens Shift Wired IR 3.5-mm, mini phono jack RS-232C Input RJ-11 female connectorVision 85 Rear Panel VHD Controller Front Panel VHD Controller Front PanelVHD Controller Rear Panel Component Video RCA connectorsHdmi 1 / Hdmi 2 Digital InputsVideo 1 / S-VIDEO Power Input 100 to 240 VACVolt 750 mA Trigger Outputs ComLink RS-232 OutputVHD Controller/Vision 85 Remote Control Vision 85 Remote Control UnitOn / OFF ENT EnterCursor Buttons Cust Memory Preset Buttons ISF NT NightVideo VID 1 2 / S-VID 2 5 S-VideoNot used Vision 85 Built-In KeypadRemote Control 3InstallationTo install batteries in the remote control OperationInstallation Installation Overview Quick SetupStep Procedure For Details, Refer to SignalsProjector Installation Options Installation ConsiderationsInstallation Type Advantages ConsiderationsThrow Distance Ceiling Installation Floor InstallationPosition Folded Optics Mounting the Vision Adjusting the ProjectionFloor Mounting Upright Ceiling Mounting InvertedConnector Panel Access Connections to the Vision 85 and VHD ControllerVHD Controller Controller Connecting SourceHdmi Connections See Figure Hdmi Source HD-DVD/BD/DVD Player or HD Tuner withDigital DTV RGB or Component Video Connections Digital DTV RGB or Component Video Connections See FigurePersonal Computer Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Composite/S-Video/Component Video Connections See FigureConnecting a PC or Outputs to ExternalEquipment 13 -volt Trigger Output Connection from Projector Connecting an External IR Receiver to the VHD Controller Adjusting the Picture Orientation Turning on the Power15. Vertical and Horizontal Lens Shift Adjustments Primary Lens AdjustmentsInstalling and Adjusting the CineWide Anamorphic Lens Adjusting the Lens Height Y Anamorphic Lens Top View 4Operation Using the On-Screen MenusService ISF PresetsInput Source Aspect RatioMain Menu Input SourceAspect Ratio Aspect Ratio Description Aspect Ratio SettingsSurface, eliminating the black bars. PictureTypical Pluge Pattern for Adjusting Brightness Perform the adjustments in the order listed hereGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Typical Test Pattern for Adjusting SharpnessInformation ISF PresetsCalibration You must enter a passcode to access the Calibration menuGain/Offset Refer to ISF Night Display Color, above Service Press Menu to exit test pattern modeCode HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Standard VisionOperation On-Screen Menus for 1080i Digital or 1080p Signals Vision 85 Main Menu 1080i Digital or 1080p Sources Only Color Temp VAC Iris Lamp Power Picture AdjustLanguage KeyISF Night Picture Adjust Advanced Effects of Primary Color Hue AdjustmentsWhite Balance HD/RGB Adj Lamp Hours read-onlyRefer to Lamp Hours onOptions Always set this option to On. Doing otherwise may disrupt Language setting Orientation Refer to Adjusting the Picture Orientation onOperation Lamp Replacement 5Maintenance and TroubleshootingTroubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution To Table Maintenance and Troubleshooting RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands 6Serial CommunicationsValue Description Min/max Stored? CommandBrightness Command Parameter Value Description Min/max Stored? Bkgnd Enter key Value Stored? DescriptionVision 85 Specifications 7SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements DimensionsVHD Controller Specifications Vision 85 Dimensions Vision 85 DimensionsPage Vidikron