Runco Vision 85 manual Gain/Offset Refer to ISF Night Display Color, above

Page 58

Operation

ISF Night - Input Image: The Input Image controls are similar to those in the Picture menu, but are accessible only by entering the Calibration menu passcode. This makes it possible to restore the picture quality settings to what they were when the projector was installed, simply by recalling the “ISF Night” preset.

ISF Night - Input Color: The Input Color controls are similar to those in the Display Color menu (see above), but can be set independently for each input.

•Gain/Offset: Refer to ISF Night - Display Color, above.

•Chroma Delay: use the Chroma Delay control to correct a mis-aligned image from a Composite, S-Video or Component video source. Chroma delay in an image causes color shifts to occur to the left of the vertical edge transitions, producing artificial shadows or a “halo” effect. If necessary, adjust this setting to eliminate them.

•Phase: Adjust the phase if the image (usually from an RGB source) shows shimmer or “noise.” Pixel phase adjusts the phase of the pixel sampling clock relative to the incoming signal. The effect of this control is similar to that of a tracking control on a VCR.

For best results, use a good test pattern such as a smooth gray consisting of a clear pattern of black and white pixels, or a similar “half on, half off” graphic image. (You may notice that you can stabilize the image at more than one point. Use either setting in this case.)

•Noise Filter: Select Noise Filter from the Input Color menu to filter a noisy Composite, S-Video or Component source signal. Adjust as desired, keeping in mind that reducing noise (which reduces high frequencies) may also soften the image.

ISF Day - Display Color: Refer to ISF Night - Display Color.

ISF Day - Input Image: Refer to ISF Night - Input Image.

ISF Day - Input Color: Refer to ISF Night - Input Color.

Save ISF Settings: Whenever you make a change to the ISF settings, you should always save it. Select Save ISF Settings from the ISF Calibration menu to do this. In the event you ever have to perform a System Reset, you can restore the saved ISF settings by selecting Restore Saved Settings in the Service menu. (System Reset and Restore Saved Settings are described on page 50.)

Output Shift: The controls in the Output Shift menu are similar to those in the Input Position menu, except that they change the characteristics of the output signal (so the change is visible no matter which input is selected). You can set these controls independently for each aspect ratio.

To save the Output Shift settings for the current aspect ratio so that they can be restored after a System Reset (described on page 50), press repeatedly to highlight “Save.” Then, press ENTER.

Splash Configure: Use the Splash Configure menu to customize the appearance of the start-up message that appears on the vacuum fluorescent display upon power-up.

•Owner Name/ISF Calibrated/ISF Other: You can have the Vision 85 display the owner’s name, your name, the phrase “ISF Calibrated” and/or any other string, up to 20 characters in length.

Use the up or down cursor button to select a character. Use the right and left cursor buttons to change the cursor position. Press MENU when you have finished entering text. Then, check the “Splash Enable” box to have the Vision 85 display the information you enter here when it is turned on.

46

Vidikron Vision 85 Owner’s Operating Manual

Page 57 Page 59
Image 58
Page 57 Page 59
Contents 1080p DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Table of Contents OperationSpecifications Maintenance and TroubleshootingSerial Communications Table of Contents 1List of Figures VHD Controller OSD Menu Structure for VisionList of Figures Xii About This Manual 1IntroductionThis Manual Performance or cause a malfunction Using This ManualThey also provide supplemental information If you need Turn toDescription, Features and Benefits Optional Accessories Controls and Functions Vision 85 at a GlanceVertical Lens Shift RS-232C Input RJ-11 female connector Wired IR 3.5-mm, mini phono jackVision 85 Rear Panel VHD Controller Front Panel VHD Controller Front PanelHdmi 1 / Hdmi 2 Digital Component Video RCA connectorsVHD Controller Rear Panel InputsVolt 750 mA Trigger Outputs Power Input 100 to 240 VACVideo 1 / S-VIDEO ComLink RS-232 OutputVision 85 Remote Control Unit VHD Controller/Vision 85 Remote ControlENT Enter On / OFFCursor Buttons Video Memory Preset Buttons ISF NT NightCust VID 1 2 / S-VID 2 5 S-VideoVision 85 Built-In Keypad Not usedTo install batteries in the remote control 3InstallationRemote Control OperationInstallation Step Procedure For Details, Refer to Quick SetupInstallation Overview SignalsInstallation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsThrow Distance Floor Installation Ceiling InstallationPosition Folded Optics Floor Mounting Upright Adjusting the ProjectionMounting the Vision Ceiling Mounting InvertedConnections to the Vision 85 and VHD Controller Connector Panel AccessVHD Controller Hdmi Connections See Figure Connecting SourceController Hdmi Source HD-DVD/BD/DVD Player or HD Tuner withDigital DTV RGB or Component Video Connections See Figure Digital DTV RGB or Component Video ConnectionsAnalog Computer RGB Connections See Figure Personal ComputerComposite/S-Video/Component Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcOutputs to External Connecting a PC orEquipment Connecting an External IR Receiver to the VHD Controller 13 -volt Trigger Output Connection from ProjectorTurning on the Power Adjusting the Picture OrientationPrimary Lens Adjustments 15. Vertical and Horizontal Lens Shift AdjustmentsInstalling and Adjusting the CineWide Anamorphic Lens Adjusting the Lens Height Y Anamorphic Lens Top View Using the On-Screen Menus 4OperationInput Source ISF PresetsService Aspect RatioInput Source Main MenuAspect Ratio Aspect Ratio Settings Aspect Ratio DescriptionPicture Surface, eliminating the black bars.Perform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input PositionISF Presets InformationYou must enter a passcode to access the Calibration menu CalibrationGain/Offset Refer to ISF Night Display Color, above Press Menu to exit test pattern mode ServiceCode Standard Vision HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUVOperation On-Screen Menus for 1080i Digital or 1080p Signals Vision 85 Main Menu 1080i Digital or 1080p Sources Only Language Picture AdjustColor Temp VAC Iris Lamp Power KeyISF Night Effects of Primary Color Hue Adjustments Picture Adjust AdvancedWhite Balance Lamp Hours read-onlyRefer to Lamp Hours on HD/RGB AdjOptions Always set this option to On. Doing otherwise may disrupt Orientation Refer to Adjusting the Picture Orientation on Language settingOperation 5Maintenance and Troubleshooting Lamp ReplacementTroubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution To Table Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration 6Serial CommunicationsCommand Value Description Min/max Stored?Brightness Command Parameter Value Description Min/max Stored? Bkgnd Value Stored? Description Enter key7Specifications Vision 85 SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsVHD Controller Specifications Vision 85 Dimensions Vision 85 DimensionsPage Vidikron
Top Page Image Contents