Runco VX-22D Installing the Optional CineWide/AutoScope Lens Motor, Remove Projector Front, Feet

Page 36

Installation

3.5

Installing the Optional CineWide/AutoScope Lens Motor

Make sure to route the wire harness in its original position and away Caution from the moving lens stages and Motor Assembly, to prevent

unexpected disconnection or lens damage.

7.Lock the lens in place by turning the Lens Locking Nut (to the left of the lens)

180 degrees counter-clockwise. (Use a 6.0mm hex wrench.)

8.Replace the Lens Cavity Front Cover.

9.Reattach the Projector Front Jewelry by sliding the top down onto the two retaining dowels. Tighten the Phillips screw at the top of the projector to secure it.

10.Remove the Front Lens Cap.

If you are installing a VX-22d with the optional CineWide with AutoScope system, proceed as follows to install the AutoScope lens motor.

1. Do not install the CineWide lens yet, only the lens motor. You will

Note install the CineWide lens after you install the projector and adjust the primary lens.

2.Some components shipped with your projector may differ slightly from what is shown in these instructions.

3.The anamorphic lens mounting kit is partially pre-assembled at the factory – the AutoScope lens motor and lens mounting assemblies are both fully assembled.

Remove Projector Front ➤	Place the projector upside down on a
Feet	blanket or other soft surface. Loosen and
	remove the two front feet on the projector.

Remove

24	Runco VX-22d Owner’s Operating Manual

Image 36

Contents VX-22d Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and Troubleshooting Table of Contents List of Figures List of Figures Xii Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions VX-22d at a GlanceVX-22d Rear Panel VX-22d Rear PanelPower Input 100 to 240 VAC Connect the VX-22d to power here USB-BDVI-DL Dual-Link DHD Controller Front Panel DHD Controller Front PanelIssue LED Service only For future use DHD Controller Rear PanelDVI-DL DUAL-LINK Output 1080p RS-232/485 Control PortVolt 750 mA Trigger Outputs Hdmi I 1 / Hdmi II 2 DigitalVX-22d Remote Control VX-22d Remote ControlPicture Adjustment Buttons BRT Brightness On / OFFSource Selection Buttons VID S-VideoMemory Preset Buttons Aspect Ratio Selection Buttons169 Lbox LetterboxInstallation Remote ControlQuick Setup Step Procedure For Details, Refer toIf installing an VX-22d/CineWide with AutoScope Installation Considerations Installation TypeAmbient Light Throw Range Throw Ratio Inches, with Lens Option 96x54-inchLens Lens Only Anamorphic Minimum MaximumCeiling Installation Floor InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Folded Optics Folded OpticsInstalling the Primary Projection Lens Other ConsiderationsInstallation Installing the Optional CineWide/AutoScope Lens Motor Remove Projector FrontFeet RemoveInstall AutoScope Lens MotorInstall Ceiling Mount Extension BracketsMounting the VX-22d Connecting the VX-22d to the DHD Controller Connections to the VX-22d and DHD ControllerConnecting Source Components to the DHD Controller Hdmi Connections See FigureHdmi Source HD-DVD/BD/DVD Player or HD Tuner with Digital DTV RGB or Component Video Connections HD1, HD2 10. Digital DTV RGB or Component Video Connections HD3 Analog Computer RGB Connections See Figure 11. Analog RGB ConnectionsVideo/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcRS-232 Controller Connection14 -volt Trigger Output Connections Connecting an External IR Receiver to the DHDDHD Controller Rear Panel Turning on the Power Adjusting the Picture OrientationConnecting to AC Power Adjustments Primary LensFocus ZoomInstalling and Adjusting the CineWide Anamorphic Lens Attach Lens Mounting Assembly to Lens Motor Carriage PlateIt is extremely important that the primary lens is properly 17. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Configure Lens Motor Trigger Adjust the Anamorphic LensInstallation Anamorphic Lens Top View Adjusting the Geometry Wrong PositionUsing the On-Screen Menus OperationISF Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio Remote Aspect Ratio Control Description Key 169 Select 169 to view 169 DVDsHdtv programs in their Native aspect ratioPicture Remote Aspect Ratio Control Description KeyPicture Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionISF Presets ISF PresetsInformation InformationCalibration Calibration ISF NightISF Day Gain/Offset Refer to ISF Night Display Color, above Service ServiceHD Format ISF Day/Night presets Maintenance and Troubleshooting Lamp ReplacementFilter Replacement Side Filter Access PanelTroubleshooting Tips Symptom Possible Causes SolutionMaintenance and Troubleshooting If you are using a PC to communicate with the DHD Controller Serial CommunicationsCommand Description Response Input Selection CommandsAspect Ratio Commands Command Description Response Image Preset Commands Menu Navigation CommandsPicture Adjust Commands Enter or Select buttonSerial Communications Specifications VX-22d SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsDHD Controller Specifications VX-22d Dimensions 1shows the VX-22d dimensions all dimensions are in inchesPage Runco CL-810 Owner’s Operating Manual