Runco VX-22D manual Gain/Offset Refer to ISF Night Display Color, above

Page 68

Operation

ISF Night - Input Color: The Input Color controls are similar to those in the Display Color menu (see above), but adjust the color balance of the incoming signal. These settings are also saved independently for each input.

•Gain/Offset: Refer to ISF Night - Display Color, above.

•Chroma Delay: use the Chroma Delay control to correct a mis-aligned image from a Composite, S-Video or Component video source. Chroma delay in an image causes color shifts to occur to the left of the vertical edge transitions, producing artificial shadows or a “halo” effect. If necessary, adjust this setting to eliminate them.

•Noise Filter: To apply noise filtering to the input signal, select Noise Filter from the Input Color menu. The Noise Filter is useful for clearing up noisy images from 480i video sources.

Use the left- or right-arrow buttons to select the desired amount of noise reduction, keeping in mind that higher settings (which reduce high frequencies) may also “soften” the image.

ISF Day - Display Color: Refer to ISF Night - Display Color.

ISF Day - Input Image: Refer to ISF Night - Input Image.

ISF Day - Input Color: Refer to ISF Night - Input Color.

Save ISF Settings: Whenever you make a change to the ISF settings, you should always save it. Select Save ISF Settings from the ISF Calibration menu to do this. In the event you ever have to perform a System Reset, you can restore the saved ISF settings by selecting Restore Saved Settings in the Service menu. (System Reset and Restore Saved Settings are described on page 58.)

Output Shift: The controls in the Output Shift menu are similar to those in the Input Position menu, except that they change the characteristics of the output signal. These settings are saved independently for each aspect ratio.

Splash Timer: Select Splash Timer from the Calibration menu to set the amount of time the Runco/ISF logo “splash” screen appears when you turn on the projector. The range is from 5 to 60 seconds, in one-second increments.

OSD Position: To adjust the position of the OSD, select OSD Position from the

Calibration menu and press ENTER (or SELECT).

Press or to select “Hor.” or “Ver.” Then, press or change the position.

56	Runco VX-22d Owner’s Operating Manual

Image 68

Contents VX-22d Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and Troubleshooting Table of Contents List of Figures List of Figures Xii Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions VX-22d at a GlanceVX-22d Rear Panel VX-22d Rear PanelDVI-DL Dual-Link Power Input 100 to 240 VAC Connect the VX-22d to power hereUSB-B DHD Controller Front Panel DHD Controller Front PanelIssue LED Service only For future use DHD Controller Rear PanelDVI-DL DUAL-LINK Output 1080p RS-232/485 Control PortVolt 750 mA Trigger Outputs Hdmi I 1 / Hdmi II 2 DigitalVX-22d Remote Control VX-22d Remote ControlPicture Adjustment Buttons BRT Brightness On / OFFSource Selection Buttons VID S-VideoMemory Preset Buttons Aspect Ratio Selection Buttons169 Lbox LetterboxInstallation Remote ControlIf installing an VX-22d/CineWide with AutoScope Quick SetupStep Procedure For Details, Refer to Ambient Light Installation ConsiderationsInstallation Type Throw Range Throw Ratio Inches, with Lens Option 96x54-inchLens Lens Only Anamorphic Minimum MaximumCeiling Installation Floor InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Folded Optics Folded OpticsInstalling the Primary Projection Lens Other ConsiderationsInstallation Installing the Optional CineWide/AutoScope Lens Motor Remove Projector FrontFeet RemoveInstall AutoScope Lens MotorInstall Ceiling Mount Extension BracketsMounting the VX-22d Connecting the VX-22d to the DHD Controller Connections to the VX-22d and DHD ControllerHdmi Source HD-DVD/BD/DVD Player or HD Tuner with Connecting Source Components to the DHD ControllerHdmi Connections See Figure Digital DTV RGB or Component Video Connections HD1, HD2 10. Digital DTV RGB or Component Video Connections HD3 Analog Computer RGB Connections See Figure 11. Analog RGB ConnectionsVideo/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcRS-232 Controller Connection14 -volt Trigger Output Connections DHD Controller Rear Panel Connecting an External IRReceiver to the DHD Connecting to AC Power Turning on the PowerAdjusting the Picture Orientation Adjustments Primary LensFocus ZoomIt is extremely important that the primary lens is properly Installing and Adjusting the CineWide Anamorphic LensAttach Lens Mounting Assembly to Lens Motor Carriage Plate 17. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Configure Lens Motor Trigger Adjust the Anamorphic LensInstallation Anamorphic Lens Top View Adjusting the Geometry Wrong PositionUsing the On-Screen Menus OperationISF Presets ServiceInput Source Aspect RatioAspect Ratio Main MenuInput Source Remote Aspect Ratio Control Description Key 169 Select 169 to view 169 DVDsHdtv programs in their Native aspect ratioPicture PictureRemote Aspect Ratio Control Description Key Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionISF Presets ISF PresetsInformation InformationISF Day CalibrationCalibration ISF Night Gain/Offset Refer to ISF Night Display Color, above HD Format ServiceService ISF Day/Night presets Maintenance and Troubleshooting Lamp ReplacementFilter Replacement Side Filter Access PanelTroubleshooting Tips Symptom Possible Causes SolutionMaintenance and Troubleshooting If you are using a PC to communicate with the DHD Controller Serial CommunicationsAspect Ratio Commands Command Description ResponseInput Selection Commands Command Description Response Image Preset Commands Menu Navigation CommandsPicture Adjust Commands Enter or Select buttonSerial Communications Specifications VX-22d SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsDHD Controller Specifications VX-22d Dimensions 1shows the VX-22d dimensions all dimensions are in inchesPage Runco CL-810 Owner’s Operating Manual