Runco VX-22D manual Installation

Page 54

Installation

Adjusting the Height (Y): With the white field still on-screen, loosen the Height/Y Adjustment T-Screws on either side of the lens. Then, slowly move the anamorphic lens into place so that there are no shadows on the top or bottom of the screen:

Too Low

Correct position

Too High

When the height is properly set, tighten the Height Adjustment T-Screws to secure the lens in place.

Pitch (Angle): Next, angle the lens to even out any top-to-bottom pincushion distortion. To do this, loosen the Pitch Adjustment T-Screws (directly below the Height/Y Adjustment T-Screws) on either side of the lens to allow it to pivot freely. Then, adjust the anamorphic lens angle so that the projected image is rectangular:

Correct Lens Angle

Incorrect Lens Angle

The anamorphic lens will almost always be angled with respect to the projector; this is normal.

Once the proper lens angle has been set, firmly tighten the Pitch Adjustment Levers to secure the lens in place.

There may be some pincushion distortion even after the lens is

Note properly adjusted, especially at shorter throw distances. If this is the case, Runco recommends that you slightly over-scan the image into the screen frame area to mask the distortion.

42	Runco VX-22d Owner’s Operating Manual

Image 54

Contents VX-22d Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and Troubleshooting Table of Contents List of Figures List of Figures Xii Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions VX-22d at a GlanceVX-22d Rear Panel VX-22d Rear PanelPower Input 100 to 240 VAC Connect the VX-22d to power here USB-BDVI-DL Dual-Link DHD Controller Front Panel DHD Controller Front PanelIssue LED DVI-DL DUAL-LINK Output 1080p Service only For future useDHD Controller Rear Panel RS-232/485 Control PortVolt 750 mA Trigger Outputs Hdmi I 1 / Hdmi II 2 DigitalVX-22d Remote Control VX-22d Remote ControlSource Selection Buttons Picture Adjustment Buttons BRT BrightnessOn / OFF VID S-Video169 Memory Preset ButtonsAspect Ratio Selection Buttons Lbox LetterboxInstallation Remote ControlQuick Setup Step Procedure For Details, Refer toIf installing an VX-22d/CineWide with AutoScope Installation Considerations Installation TypeAmbient Light Lens Throw Range Throw Ratio Inches, with Lens Option96x54-inch Lens Only Anamorphic Minimum MaximumVertical and Horizontal Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Example only Folded Optics Folded OpticsInstalling the Primary Projection Lens Other ConsiderationsInstallation Feet Installing the Optional CineWide/AutoScope Lens MotorRemove Projector Front RemoveInstall AutoScope Lens MotorInstall Ceiling Mount Extension BracketsMounting the VX-22d Connecting the VX-22d to the DHD Controller Connections to the VX-22d and DHD ControllerConnecting Source Components to the DHD Controller Hdmi Connections See FigureHdmi Source HD-DVD/BD/DVD Player or HD Tuner with Digital DTV RGB or Component Video Connections HD1, HD2 10. Digital DTV RGB or Component Video Connections HD3 Analog Computer RGB Connections See Figure 11. Analog RGB ConnectionsVideo/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcRS-232 Controller Connection14 -volt Trigger Output Connections Connecting an External IR Receiver to the DHDDHD Controller Rear Panel Turning on the Power Adjusting the Picture OrientationConnecting to AC Power Focus AdjustmentsPrimary Lens ZoomInstalling and Adjusting the CineWide Anamorphic Lens Attach Lens Mounting Assembly to Lens Motor Carriage PlateIt is extremely important that the primary lens is properly 17. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Configure Lens Motor Trigger Adjust the Anamorphic LensInstallation Anamorphic Lens Top View Adjusting the Geometry Wrong PositionUsing the On-Screen Menus OperationInput Source ISF PresetsService Aspect RatioMain Menu Input SourceAspect Ratio Hdtv programs in their Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Native aspect ratioPicture Remote Aspect Ratio Control Description KeyPicture Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionInformation ISF PresetsISF Presets InformationCalibration Calibration ISF NightISF Day Gain/Offset Refer to ISF Night Display Color, above Service ServiceHD Format ISF Day/Night presets Maintenance and Troubleshooting Lamp ReplacementFilter Replacement Side Filter Access PanelTroubleshooting Tips Symptom Possible Causes SolutionMaintenance and Troubleshooting If you are using a PC to communicate with the DHD Controller Serial CommunicationsCommand Description Response Input Selection CommandsAspect Ratio Commands Picture Adjust Commands Command Description Response Image Preset CommandsMenu Navigation Commands Enter or Select buttonSerial Communications Specifications VX-22d SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsDHD Controller Specifications VX-22d Dimensions 1shows the VX-22d dimensions all dimensions are in inchesPage Runco CL-810 Owner’s Operating Manual