Runco VX-22D manual Maintenance and Troubleshooting, Lamp Replacement

Page 71

5. Maintenance and Troubleshooting

The lamp should be replaced when it reaches the end of its life (typically 2000 hours), or sooner if a noticeable degradation in brightness occurs. When you replace a lamp, you should replace the filters as well.

For lamp or filter replacement, please contact your nearest Runco authorized service center or Runco dealer. Do not attempt to replace the lamp yourself!

WARNING

The VX-22d lamp is under high pressure. Handle it with great care

at all times. Lamps may explode if dropped or mishandled.

Never attempt to disassemble the lamp casing or dispose of the lamp casing in any manner other than by returning it to your Runco dealer.

If the lamp breaks, leave the area immediately and stay away for at least 30 minutes. Ventilate the room to allow the mercury vapor to disperse.

If you inhale the mercury vapor, see a physician immediately.

5.1

Lamp Replacement

1.Turn off the projector and unplug the power cord. Allow the projector to cool down for approximately 45 minutes prior to removing the lamp assembly for replacement.

2.Loosen and remove the rear Lamp Cover screw.

3.Slide the Lamp Cover in the direction of the arrow to remove it.

4.Loosen the two, captive lamp assembly

mounting screws using a coin or a large, flat-blade screwdriver.

5.Grasp the lamp assembly handle and pull gently, removing the lamp module from the projector housing.

Runco VX-22d Owner’s Operating Manual

59

Image 71
Contents VX-22d Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and Troubleshooting Table of Contents List of Figures List of Figures Xii About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories VX-22d at a Glance Controls and FunctionsVX-22d Rear Panel VX-22d Rear PanelDVI-DL Dual-Link Power Input 100 to 240 VAC Connect the VX-22d to power hereUSB-B DHD Controller Front Panel DHD Controller Front PanelIssue LED RS-232/485 Control Port Service only For future useDHD Controller Rear Panel DVI-DL DUAL-LINK Output 1080pHdmi I 1 / Hdmi II 2 Digital Volt 750 mA Trigger OutputsVX-22d Remote Control VX-22d Remote ControlVID S-Video Picture Adjustment Buttons BRT BrightnessOn / OFF Source Selection ButtonsLbox Letterbox Memory Preset ButtonsAspect Ratio Selection Buttons 169Remote Control InstallationIf installing an VX-22d/CineWide with AutoScope Quick SetupStep Procedure For Details, Refer to Ambient Light Installation ConsiderationsInstallation Type Lens Only Anamorphic Minimum Maximum Throw Range Throw Ratio Inches, with Lens Option96x54-inch LensPosition Ceiling InstallationFloor Installation Vertical and HorizontalHorizontal Lens Shift Example only Folded Optics Folded OpticsOther Considerations Installing the Primary Projection LensInstallation Remove Installing the Optional CineWide/AutoScope Lens MotorRemove Projector Front FeetMotor Install AutoScope LensExtension Brackets Install Ceiling MountMounting the VX-22d Connections to the VX-22d and DHD Controller Connecting the VX-22d to the DHD ControllerHdmi Source HD-DVD/BD/DVD Player or HD Tuner with Connecting Source Components to the DHD ControllerHdmi Connections See Figure Digital DTV RGB or Component Video Connections HD1, HD2 10. Digital DTV RGB or Component Video Connections HD3 11. Analog RGB Connections Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Video/Composite Video Connections See FigureConnection RS-232 Controller14 -volt Trigger Output Connections DHD Controller Rear Panel Connecting an External IRReceiver to the DHD Connecting to AC Power Turning on the PowerAdjusting the Picture Orientation Zoom AdjustmentsPrimary Lens FocusIt is extremely important that the primary lens is properly Installing and Adjusting the CineWide Anamorphic LensAttach Lens Mounting Assembly to Lens Motor Carriage Plate 17. Attaching the Anamorphic Lens to the Lens Adapter Ring Configure Lens Motor Trigger Adjust the Anamorphic Lens Adjusting the Horizontal X Lens PositionInstallation Anamorphic Lens Top View Wrong Position Adjusting the GeometryOperation Using the On-Screen MenusAspect Ratio ISF PresetsService Input SourceAspect Ratio Main MenuInput Source Native aspect ratio Remote Aspect Ratio Control Description Key 169Select 169 to view 169 DVDs Hdtv programs in theirPicture PictureRemote Aspect Ratio Control Description Key Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionInformation ISF PresetsISF Presets InformationISF Day CalibrationCalibration ISF Night Gain/Offset Refer to ISF Night Display Color, above HD Format ServiceService ISF Day/Night presets Lamp Replacement Maintenance and TroubleshootingSide Filter Access Panel Filter ReplacementSymptom Possible Causes Solution Troubleshooting TipsMaintenance and Troubleshooting Serial Communications If you are using a PC to communicate with the DHD ControllerAspect Ratio Commands Command Description ResponseInput Selection Commands Enter or Select button Command Description Response Image Preset CommandsMenu Navigation Commands Picture Adjust CommandsSerial Communications VX-22d Specifications SpecificationsDimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power RequirementsDHD Controller Specifications 1shows the VX-22d dimensions all dimensions are in inches VX-22d DimensionsPage Runco CL-810 Owner’s Operating Manual