Runco VX-6000D Lens Replacement, Only trained, authorized Runco dealers should attempt to

Page 90

Maintenance and Troubleshooting

5.2

Lens Replacement

Figure 5-1shows the VX-6000d lens assembly.

Motor Assembly

9/64” Hex Screw (6x) for Mounting Lens

	Motor Assembly
	Electrical Connector
Front of Lens	and Harness
Projector Front Jewelry

Figure 5-1. VX-6000d Lens Assembly Exploded View

Only trained, authorized Runco dealers should attempt to

Note remove or replace a lens. Please read this procedure carefully before doing so.

Lens replacement is normally performed at the Runco factory. Field replacement of lenses is generally only required if the projector is re-installed in a new location or the lens has been damaged.

1.Remove the Projector Front Jewelry by loosening the captive #2 Phillips screw below the lens.

74	Runco VX-6000d Installation/Operation Manual

Image 90

Contents VX-6000d VX-6000d VX-6000d/CineWide VX-6000d/CineWide with AutoScopePage RuncoCare Standard Two Year Limited Warranty RuncoCare Standard FeaturesRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Compliance Information Declaration of ConformityFCC Part Page Table of Contents Ceiling Mounting Inverted Operation Maintenance and TroubleshootingSpecifications External ControlTable of Contents Xiv List of Figures Xvi Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Format screenOptional Accessories Controls and Functions VX-6000d at a GlanceVertical Lens Shift RS-232C RJ-11 female connector VX-6000d Rear PanelDHD Controller Front Panel DHD Controller Front PanelDHD Controller Rear PanelDisplay Control Inputs 4. USB VX-6000d Remote Control Units Standard DHD Remote ControlOn / OFF Cursor ButtonsComp Component 169 Memory Preset ButtonsAspect Ratio Selection Buttons Letbox LetterboxVX6K Setup Remote Control FunctionsControls and Functions Battery Installation InstallationRemote Control Setup Remote Standard DHD RemoteOperation Other surfacesQuick Setup Installation OverviewStep Procedure For Details, Refer to Installation Type InstallationProjector Installation Options ConsiderationsVX-6000d Lens Options and Throw Ratios Throw DistanceVertical and Horizontal Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Example Only Vertical and Horizontal Lens Shift Limits Folded Optics Synchronization IssuesPossible Audio Latency for Various Input/Output Timings Audio/VideoInstalling the Optional CineWide Lens Mount Other Considerations7shows the VX-6000d/CineWide with AutoScope motor assembly VX-6000d with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation CineWide Base Plate VX-6000d/CineWideMounting the VX-6000d Connections to the VX-6000d and DHD Controller10. Connecting the VX-6000d to the DHD Controller Hdmi Source Connections See Figure Connecting SourceComponents to the DHD Controller12. Component Video Source Connections DTV-Set-Top BoxComputer RGB Camcorder 13. Rgbhv Source ConnectionsGaming Console 14. Scart Rgbs Source ConnectionsComposite and S-Video Source Connections CamcorderRS-232 Controller ConnectionConnecting 12-volt Trigger Outputs to External Equipment AutoScope Lens Motor18 -volt Trigger Output Connection from Projector Connecting an External IR Receiver to the DHD Controller 19. External IR Receiver ConnectionTurning on the Power HdmiPrimary Lens Adjustments Focus Zoom Iris Vertical and Horizontal Lens ShiftAdjusting the Picture Orientation Vertical HorizontalInstalling and Adjusting the CineWide Anamorphic Lens It is extremely important that the primary lens is properly22. Attaching the Anamorphic Lens to the Lens Adapter Ring Select Triggers from the Service menu Adjusting the Horizontal X Lens PositionInstallation Adjusting the Geometry Anamorphic Lens Top ViewInstallation Using the On-Screen Menus OperationService Main MenuRunco Video Input Source Input SourceAspect Ratio Aspect RatioSelect 169 to view 169 DVDs Aspect Ratio SettingsRemote Aspect Ratio Control Description Button 169 Hdtv programs in theirRemote Aspect Ratio Control Description Button OverscanPicture PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Input Position Input PositionAdjust the Phase after adjusting Tracking see below Memory Presets Memory PresetsInformation CalibrationShould be used by ISF-certified technicians only CIE 1931 Chromaticity Diagram Color Temperature Presets and Associated Color Points Color Temperature Preset Associated x/y ValuesCopied settings are not retained after a power cycle Copy/PasteService ServiceInput Names Exit Operation Operation 63 and ISF Day/Night Memory Presets Maintenance and Troubleshooting Lamp ReplacementLens Replacement Only trained, authorized Runco dealers should attempt toMaintenance and Troubleshooting Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Troubleshooting Chart Maintenance and Troubleshooting External Control Port ConfigurationSerial Command Syntax Serial CommunicationsSerial Commands Input Selection CommandsPicture Adjust Commands Input Position Commands Output Shift CommandsEnter key Exit Return keyUsing Discrete IR Codes Command BitsWith Toggle Bit = Hex Binary Function Start RC5 Control Codes for the DHD Controller IR Command ListRemote Control With Toggle Description Button Name Bit = RC5 DataEnter Specifications VX-6000d SpecificationsVX-6000d Specifications Power Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsDHD Controller Specifications DHD Controller SpecificationsVX-6000d Dimensions VX-6000d/CineWide Dimensions with Optional Ceiling MountSupported Timings Supported Signal Timings by InputFormat Resolution Frequency Rate Hz MHz KHz Supported? √ = Yes, = NoPAL-B/G/H/I PAL-M Specifications Page 020-0769-02 Rev. B May

Related manuals

Manual 102 pages 53.58 Kb