Sharp PG-D3510X, PG-D2710X, PG-D3010X appendix Accessories, Optional accessories

Page 15

Accessories

Supplied accessories

Two R-6 batteries

 

(“AA” size, UM/SUM-3,

RGB cable

 

HP-7 or similar)

 

(10' (3.0 m))

 

 

 

 

 

 

<QCNWGA086WJPZ>

Remote control

 

 

 

<RRMCGA837WJSA>

 

 

 

 

DIN-D-sub RS-232C adaptor

 

 

(5 57/64 " (15 cm))

Storage case

 

<QCNWGA091WJPZ>

<GCASNA024WJSA>

Power cord*

 

 

 

(1)

(2)

(3)

(4)

For U.S. and

For Europe,

For U.K. and

For Australia, New

Canada, etc.

except U.K.

Singapore

Zealand and Oceania

(6' (1.8 m))

(6' (1.8 m))

(6' (1.8 m))

(6' (1.8 m))

<QACCDA007WJPZ>

<QACCVA011WJPZ>

<QACCBA036WJPZ> <QACCLA018WJPZ>

*Which power cords are supplied along with your projector depends on the region. Use the power cord that corresponds to the wall outlet in your country.

Operation manuals (this manual <TINS-E390WJZZ>, OPERATION MANUAL FOR STEREOSCOPIC 3D PROJECTION <TINS-E500WJZZ> and CD-ROM <UDSKAA121WJZZ>)

Note

• Codes in “< >” are Replacement parts codes.

Optional accessories

■ Lamp unit

AN-D350LP

Ceiling-mount adaptor

AN-60KT

Ceiling-mount bracket

AN-XRCM30 (for U.S.A. only)

Ceiling-mount unit

AN-TK201 <for AN-60KT>

 

AN-TK202 <for AN-60KT>

Ceiling-mount extension tube

AN-EP101B <for AN-XRCM30>

 

(for U.S.A. only)

■ Remote receiver

AN-MR2

■ 3 RCA to mini D-sub 15 pin cable (10 n (3.0 m))

AN-C3CP2

Note

Some of the optional accessories may not be available depending on the region. Please check with your nearest Sharp Authorized Projector Dealer or Service Center.

Introduction

11

Image 15
Contents PG-D3510X PG-D3010X PG-D2710X Model No Serial No Iii Page Void the users authority to operate this equipment See bottom of projectorInformation Product Disposal Maintenance Troubleshooting Index Using the Menu ScreenFor Future Reference Contents Reference Adjusting the Projector Function PRJ ADJ1/2 MenuPower-Cord Protection CleaningPower Sources AccessoriesOverloading Damage Requiring ServiceReplacement Parts Safety CheckAvoid locations with extremes of temperature Rest your eyes occasionallyDo not block the exhaust and intake vents Closed Caption uses Bitstream Vera fonts Using the projector in other countriesTemperature monitor function Other connected equipmentWhen you want to view the Setup Manual For WindowsFor Macintosh Optional accessories AccessoriesFront View Part Names and FunctionsRear View Terminals Using the Kensington LockPicture Mode button For automatically adjusting images whenVOL +/- Volume buttons Break Timer buttonRemote control signal transmitters Inserting the BatteriesUsable Range Easy Start Setup and ProjectionWhen connecting equipment other than a computer, see pages On the projector On the remote controlTurn the computer on Turn the power off Setting Up the Projector Setting Up the ProjectorStandard Setup Front Projection Screen Lens center Signal Input Normal ModeSignal Input 169 Mode Screen Size and Projection DistanceCeiling-Mount Setup Projection PRJ ModeTerminals on the Projector Connecting the Projector to Other EquipmentConnecting the Projector to Other Equipment RGB Controlling the Projector by a Computer Connecting the Power Cord When connecting to the LAN terminal using a LAN cableAC socket To AC outlet Power cord supplied Standby button On button Power indicator Lamp indicatorTurning the Projector On/Off Turning the Projector OnImage Projection About the Setup GuideAdjusting the Projected Image Adjusting the Focus Press Enter to exit the Setup Guide screenMake small adjustments Height Adjust lever Adjusting the HeightAdjusting the Picture Size Use the rear adjustment foot to make the projector levelPress Keystone Press Keystone to enter the Keystone Correction modePress P/Q or O/R to adjust Keystone Correction Correcting Trapezoidal DistortionOn-screen display Switching the Input ModeAdjusting the Volume Input buttons AV Mute button VOL +/- Volume buttons ButtonsPress Resize Resize ModeAbout Copyrights Switching the Eco+Quiet Mode Operating with the Remote ControlDisplaying and Setting the Break Timer Using the Spot FunctionFreezing a Moving Image Selecting the Picture ModeWhen right-clicking Using the Remote Control as the Wireless Computer MouseWhen moving the cursor When left-clickingPicture menu Menu ItemsMain menu Network menu Example Using the Menu ScreenMenu Selections Quick Start Menu Press MenuFollowing items can be configured on the Quick Start Menu Example Adjusting BrightQuick Start Menu Menu Selections Complete MenuPress Enter To adjust the projected image while watching itPress P or R and select Bright to adjust Press O or Q to adjust the item selectedPicture Adjustment Picture Menu Selecting the Picture ModeMenu operation n Adjusting Hue, Saturation, or Value Adjusting the ImageAdjusting the Color Temperature Adjusting the ColorsSelecting the Film Mode Eco+QuietReducing Image Noise DNR Signal Adjustment SIG-ADJ Menu Signal Type SettingResolution Setting When reproducing Ntsc signals in PAL video equipment Setting the Video SetupKeystone Correction Adjusting the Projected Image SCR-ADJ MenuSetting the Resize Mode Adjusting the Image PositionFor Americas only Setting the OverscanSetting the On-screen Display Closed CaptionSelecting the Wall Color Selecting the Setup GuideSelecting the Background Image Reversing/Inverting Projected ImagesAuto Restart Function Auto Sync Auto Sync AdjustmentAuto Power Off Function Speaker SettingPress the 4 buttons on the remote Fan Mode SettingPreset keycode in Old Code System Lock FunctionCOMPUTER2 Select Adjusting the Projector Function PRJ-ADJ1/2 MenuKeylock Function Selecting the Quick Start MenuChecking the Lamp Life Status Setting the Function Button OperationStandby Mode Returning to the Default SettingsOn the projector, press Setting a PasswordSelect Password, then press Enter or Q Enter the same password in Reconfirm, then press EnterEnter IP Address using P, R, Q O, then press Enter Dhcp Client SettingTCP/IP Setting Returning to Default Settings NetworkSetting Up the Projector Network Environment Network Menu Confirming the Projector InformationYou can confirm the following items Cleaning the exhaust and intake vents MaintenanceCleaning the projector Cleaning the lensMaintenance Indicators About the temperature warning indicatorAbout the lamp indicator Red on Abnormally high Are high Lower than 95F +35ºC Regarding the Lamp LampReplacing the Lamp STANDBY/ON button AC socket Removing and Installing the Lamp UnitRemove the lamp unit cover Lamp unitResetting the Lamp Timer Place the projector into the storage case How to Use the Storage CaseStoring the Projector Open the cover of the storage caseComputer Computer Compatibility Chart21-25 Troubleshooting57, 58 Sharp Electronics Corporation Specifications Dimensions Index
Related manuals
Manual 26 pages 18.55 Kb