Sharp PG-D3510X, PG-D2710X, PG-D3010X Turning the Projector On/Off, Power indicator Lamp indicator

Page 30

Turning the Projector On/Off

Turning the Projector On

Note that the connections to external equipment and power outlet should be done before performing the operations written below. (See pages 21 to 25.)

Open the lens shutter fully and press STANDBY/ON on the projector or ON on the remote control.

•The power indicator illuminates green.

•After the lamp indicator illuminates, the projector is ready to start operation.

Note

•About the Lamp Indicator

The lamp indicator illuminates to indicate the status of the lamp.

Green: The lamp is on.

Blinking in green: The lamp is warming up.

Red: The lamp is shut down abnormally or the lamp should be replaced.

•When switching on the projector, a slight

ﬂ ickering of the image may be experienced within the ﬁ rst minute after the lamp has been illuminated. This is normal operation as the lamp's control circuitry is stabilising the lamp output characteristics. It should not be regarded as faulty operation.

•If the projector is put into Standby mode and immediately turned on again, the lamp may take some time to start projection.

•When System Lock is set, the keycode input box appears. To cancel the keycode setting, input the keycode that you have already set. See page 51 for details.

Info

•When “Auto Restart” is set to “On”:

If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on. (See page 50.)

•English is the factory default language. If you want to change the on-screen display to another language, change the language according to the procedure on page 49.

Power indicator Lamp indicator

STANDBY/ON button

STANDBY button

ON button

Turning the Power Off (Putting the Projector into Standby Mode)

Press STANDBY/ON on the projector or STANDBY on the remote control, then press that button again while the conﬁrmation message is displayed, to put the projector into Standby mode.

• The projector cannot be turned on while cooling.

On-screen display (conﬁrmation message)

Info

•Direct Power Off function:

You can unplug the power cord from the AC outlet even if the cooling fan is still running.

26

Image 30

Contents PG-D3510X PG-D3010X PG-D2710X Model No Serial No Iii Page See bottom of projector Void the users authority to operate this equipmentInformation Product Disposal Maintenance Troubleshooting Index Using the Menu ScreenFor Future Reference Contents Adjusting the Projector Function PRJ ADJ1/2 Menu ReferenceAccessories CleaningPower Sources Power-Cord ProtectionSafety Check Damage Requiring ServiceReplacement Parts OverloadingAvoid locations with extremes of temperature Rest your eyes occasionallyDo not block the exhaust and intake vents Other connected equipment Using the projector in other countriesTemperature monitor function Closed Caption uses Bitstream Vera fontsWhen you want to view the Setup Manual For WindowsFor Macintosh Accessories Optional accessoriesPart Names and Functions Front ViewUsing the Kensington Lock Rear View TerminalsBreak Timer button For automatically adjusting images whenVOL +/- Volume buttons Picture Mode buttonRemote control signal transmitters Inserting the BatteriesUsable Range On the projector On the remote control Setup and ProjectionWhen connecting equipment other than a computer, see pages Easy StartTurn the computer on Turn the power off Setting Up the Projector Setting Up the ProjectorStandard Setup Front Projection Screen Size and Projection Distance Signal Input Normal ModeSignal Input 169 Mode Screen Lens centerProjection PRJ Mode Ceiling-Mount SetupConnecting the Projector to Other Equipment Terminals on the ProjectorConnecting the Projector to Other Equipment RGB Controlling the Projector by a Computer Connecting the Power Cord When connecting to the LAN terminal using a LAN cableAC socket To AC outlet Power cord supplied Turning the Projector On Power indicator Lamp indicatorTurning the Projector On/Off Standby button On buttonPress Enter to exit the Setup Guide screen About the Setup GuideAdjusting the Projected Image Adjusting the Focus Image ProjectionUse the rear adjustment foot to make the projector level Adjusting the HeightAdjusting the Picture Size Make small adjustments Height Adjust leverCorrecting Trapezoidal Distortion Press Keystone to enter the Keystone Correction modePress P/Q or O/R to adjust Keystone Correction Press KeystoneInput buttons AV Mute button VOL +/- Volume buttons Buttons Switching the Input ModeAdjusting the Volume On-screen displayResize Mode Press ResizeAbout Copyrights Using the Spot Function Operating with the Remote ControlDisplaying and Setting the Break Timer Switching the Eco+Quiet ModeSelecting the Picture Mode Freezing a Moving ImageWhen left-clicking Using the Remote Control as the Wireless Computer MouseWhen moving the cursor When right-clickingMenu Items Picture menuMain menu Network menu Press Menu Using the Menu ScreenMenu Selections Quick Start Menu ExampleMenu Selections Complete Menu Example Adjusting BrightQuick Start Menu Following items can be conﬁgured on the Quick Start MenuPress O or Q to adjust the item selected To adjust the projected image while watching itPress P or R and select Bright to adjust Press EnterPicture Adjustment Picture Menu Selecting the Picture ModeMenu operation n Adjusting the Colors Adjusting the ImageAdjusting the Color Temperature Adjusting Hue, Saturation, or ValueSelecting the Film Mode Eco+QuietReducing Image Noise DNR Signal Adjustment SIG-ADJ Menu Signal Type SettingResolution Setting Setting the Video Setup When reproducing Ntsc signals in PAL video equipmentAdjusting the Image Position Adjusting the Projected Image SCR-ADJ MenuSetting the Resize Mode Keystone CorrectionClosed Caption Setting the OverscanSetting the On-screen Display For Americas onlyReversing/Inverting Projected Images Selecting the Setup GuideSelecting the Background Image Selecting the Wall ColorSpeaker Setting Auto Sync Auto Sync AdjustmentAuto Power Off Function Auto Restart FunctionSystem Lock Function Fan Mode SettingPreset keycode in Old Code Press the 4 buttons on the remoteSelecting the Quick Start Menu Adjusting the Projector Function PRJ-ADJ1/2 MenuKeylock Function COMPUTER2 SelectReturning to the Default Settings Setting the Function Button OperationStandby Mode Checking the Lamp Life StatusEnter the same password in Reconﬁrm, then press Enter Setting a PasswordSelect Password, then press Enter or Q On the projector, pressReturning to Default Settings Network Dhcp Client SettingTCP/IP Setting Enter IP Address using P, R, Q O, then press EnterSetting Up the Projector Network Environment Network Menu Conﬁrming the Projector InformationYou can conﬁrm the following items Cleaning the lens MaintenanceCleaning the projector Cleaning the exhaust and intake ventsMaintenance Indicators About the temperature warning indicatorAbout the lamp indicator Red on Abnormally high Are high Lower than 95F +35ºC Regarding the Lamp LampReplacing the Lamp Lamp unit Removing and Installing the Lamp UnitRemove the lamp unit cover STANDBY/ON button AC socketResetting the Lamp Timer Open the cover of the storage case How to Use the Storage CaseStoring the Projector Place the projector into the storage caseComputer Compatibility Chart ComputerTroubleshooting 21-2557, 58 Sharp Electronics Corporation Speciﬁcations Dimensions Index

Related manuals

Manual 26 pages 18.55 Kb