Sharp PG-D2710X, PG-D3510X, PG-D3010X Setting a Password, Select Password, then press Enter or Q

Page 58

Setting Up the Projector Network Environment (“Network” Menu)

Menu operation n Page 40

Pict. SIG SCR PRJ1 PRJ2 Network

1

 

Password

Disable

 

2

 

DHCP Client

Off

 

3 TCP/IP

4 Reset Network Setting

5 Restart Network

 

 

 

 

 

 

 

 

 

 

IP Address

XXX.XXX.XXX.XXX

 

 

6

 

 

MAC Address

XX : XX : XX : XX : XX : XX

 

 

 

Projector

XX-XXXX

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Link

￿ Disconnected

 

 

 

 

 

 

 

 

 

 

 

 

SEL./ADJ.

ENTER

END

1 Setting a Password

If you do not want others to change the setting for the “Network” menu, set a password.

2 Enter the password in “Old Password” using P, R, Q and O, then press ENTER.

a Setting a Password

1 Select “Password”, then press ENTER or Q.

The screen for entering the password appears.

Network

Setting the Password

 

 

 

 

Old Password

– – – –

New Password

Reconfirm

– – – –

2 Press P or R to set the first digit

in “New Password”, then press Q.

3 Enter the remaining 3 digits, then press ENTER.

• To return to the previous digit, press O.

4 Enter the same password in “Reconfirm”, then press ENTER.

The status for “Password” changes to “Enable”.

3 Enter the password in “New Password” using P, R, Q and O, then press ENTER.

4 Enter the same password again in “Reconfirm” using P, R, Q and O, then press ENTER.

Note

If you do not need the password protection for the “Network” menu settings anymore, press ENTER without entering the new password in steps 3 and 4.

To cancel the password settings, press

RETURN.

If you forget the password

If you forget the password, perform the following procedure to delete it, then set a new password.

Note

Once the password is set, you must enter the password to change the “Network” menu settings.

a Changing the Password

1 Select “Password”, then press ENTER or Q.

The screen for entering the password appears.

On the projector, press

.

Note

If ENTER is held down for more than 5 seconds, the operation buttons on the projector will be locked. (See page 52.)

You cannot use the buttons on the remote control to delete the password.

54

Image 58
Contents PG-D3510X PG-D3010X PG-D2710X Model No Serial No Iii Page See bottom of projector Void the users authority to operate this equipmentInformation Product Disposal Using the Menu Screen Maintenance Troubleshooting IndexFor Future Reference Contents Adjusting the Projector Function PRJ ADJ1/2 Menu ReferenceAccessories CleaningPower Sources Power-Cord ProtectionSafety Check Damage Requiring ServiceReplacement Parts OverloadingRest your eyes occasionally Avoid locations with extremes of temperatureDo not block the exhaust and intake vents Other connected equipment Using the projector in other countriesTemperature monitor function Closed Caption uses Bitstream Vera fontsFor Windows When you want to view the Setup ManualFor Macintosh Accessories Optional accessoriesPart Names and Functions Front ViewUsing the Kensington Lock Rear View TerminalsBreak Timer button For automatically adjusting images whenVOL +/- Volume buttons Picture Mode buttonInserting the Batteries Remote control signal transmittersUsable Range On the projector On the remote control Setup and ProjectionWhen connecting equipment other than a computer, see pages Easy StartTurn the computer on Turn the power off Setting Up the Projector Setting Up the ProjectorStandard Setup Front Projection Screen Size and Projection Distance Signal Input Normal ModeSignal Input 169 Mode Screen Lens centerProjection PRJ Mode Ceiling-Mount SetupConnecting the Projector to Other Equipment Terminals on the ProjectorConnecting the Projector to Other Equipment RGB Controlling the Projector by a Computer When connecting to the LAN terminal using a LAN cable Connecting the Power CordAC socket To AC outlet Power cord supplied Turning the Projector On Power indicator Lamp indicatorTurning the Projector On/Off Standby button On buttonPress Enter to exit the Setup Guide screen About the Setup GuideAdjusting the Projected Image Adjusting the Focus Image ProjectionUse the rear adjustment foot to make the projector level Adjusting the HeightAdjusting the Picture Size Make small adjustments Height Adjust leverCorrecting Trapezoidal Distortion Press Keystone to enter the Keystone Correction modePress P/Q or O/R to adjust Keystone Correction Press KeystoneInput buttons AV Mute button VOL +/- Volume buttons Buttons Switching the Input ModeAdjusting the Volume On-screen displayResize Mode Press ResizeAbout Copyrights Using the Spot Function Operating with the Remote ControlDisplaying and Setting the Break Timer Switching the Eco+Quiet ModeSelecting the Picture Mode Freezing a Moving ImageWhen left-clicking Using the Remote Control as the Wireless Computer MouseWhen moving the cursor When right-clickingMenu Items Picture menuMain menu Network menu Press Menu Using the Menu ScreenMenu Selections Quick Start Menu ExampleMenu Selections Complete Menu Example Adjusting BrightQuick Start Menu Following items can be configured on the Quick Start MenuPress O or Q to adjust the item selected To adjust the projected image while watching itPress P or R and select Bright to adjust Press EnterSelecting the Picture Mode Picture Adjustment Picture MenuMenu operation n Adjusting the Colors Adjusting the ImageAdjusting the Color Temperature Adjusting Hue, Saturation, or ValueEco+Quiet Selecting the Film ModeReducing Image Noise DNR Signal Type Setting Signal Adjustment SIG-ADJ MenuResolution Setting Setting the Video Setup When reproducing Ntsc signals in PAL video equipmentAdjusting the Image Position Adjusting the Projected Image SCR-ADJ MenuSetting the Resize Mode Keystone CorrectionClosed Caption Setting the OverscanSetting the On-screen Display For Americas onlyReversing/Inverting Projected Images Selecting the Setup GuideSelecting the Background Image Selecting the Wall ColorSpeaker Setting Auto Sync Auto Sync AdjustmentAuto Power Off Function Auto Restart FunctionSystem Lock Function Fan Mode SettingPreset keycode in Old Code Press the 4 buttons on the remoteSelecting the Quick Start Menu Adjusting the Projector Function PRJ-ADJ1/2 MenuKeylock Function COMPUTER2 SelectReturning to the Default Settings Setting the Function Button OperationStandby Mode Checking the Lamp Life StatusEnter the same password in Reconfirm, then press Enter Setting a PasswordSelect Password, then press Enter or Q On the projector, pressReturning to Default Settings Network Dhcp Client SettingTCP/IP Setting Enter IP Address using P, R, Q O, then press EnterConfirming the Projector Information Setting Up the Projector Network Environment Network MenuYou can confirm the following items Cleaning the lens MaintenanceCleaning the projector Cleaning the exhaust and intake ventsAbout the temperature warning indicator Maintenance IndicatorsAbout the lamp indicator Red on Abnormally high Are high Lower than 95F +35ºC Lamp Regarding the LampReplacing the Lamp Lamp unit Removing and Installing the Lamp UnitRemove the lamp unit cover STANDBY/ON button AC socketResetting the Lamp Timer Open the cover of the storage case How to Use the Storage CaseStoring the Projector Place the projector into the storage caseComputer Compatibility Chart ComputerTroubleshooting 21-2557, 58 Sharp Electronics Corporation Specifications Dimensions Index
Related manuals
Manual 26 pages 18.55 Kb