Vidikron operation manual Vision 110 Rear Panel

Page 20

Controls and Functions

2.2

Vision 110 Rear Panel

Figure 2-2shows the Vision 110 rear panel.

16

15

14

13

HD3 (VGA / Y-Pb-Pr)

Pr)-Pb-Y / (VGA HD3

HD2 (BNC)

(BNC) HD2

.cover lamp the off pull to screw the Remove

Remove the screw to pull off the lamp cover.

WIRED REMOTE

REMOTE WIRED

Service port. Not for user access

HD1 (RCA)

(RCA) HD1

SERVICE PORT

AUTHORIZED

PERSONNEL ONLY

L

L

2	4	6	8	10	12
1	3	5	7	9	11

Figure 2-2. Vision 110 Rear Panel

1.LAMP COVER

Remove this cover to access the lamp compartment.

2.VACUUM FLUORESCENT DISPLAY (VFD)

Can be used instead of the OSD. Displays currently-selected menu or – if no menu is selected – the current source, input resolution and aspect ratio.

If an error condition occurs, a message

appears here indicating the cause:	Please check issue(s)
appears here indicating the cause:
	Communication Error

3.RUN LED

–Lights blue to indicate that the projector is functioning normally.

–Flashes blue (one second on/one second off) to indicate an error condition.

–Flashes blue (one half-second on/one half-second off) for approximately 90 seconds after the system is turned off.

4.ISSUE LED

Lights red to indicate an error condition.

6	Vidikron Vision Model 110 Installation/Operation Manual

Image 20

Contents 110 Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Important Safety Instructions Compliance Information Declaration of ConformityFCC Part 1Table of Contents Attach Lens Mounting Assembly to Lens Motor Carriage Plate OperationMaintenance and Troubleshooting Table of Contents Xii 1List of Figures List of Figures Xiv 1Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Vision 110 offers these key features and benefitsOptional Accessories Controls and Functions Vision 110 at a GlanceVision 110 Rear Panel Vision 110 Rear PanelSTAND-BY LED Vision 110 Rear Connector Panel Service only For future useRS-232/485 Control Port Volt 750 mA Trigger OutputsHdmi I 1 / Hdmi II 2 Digital HD3 InputVision 110 Remote Control Vision 110 Remote ControlPicture Adjustment Buttons BRT Brightness On / OFFSource Selection Buttons VID S-VideoMemory Preset Buttons Aspect Ratio Selection Buttons169 Lbox LetterboxOperation 3InstallationRemote Control Quick Setup Installation OverviewStep Procedure For Details, Refer to If installing a Vision 110/CineWide or VisionInstallation Considerations Projector Installation OptionsInstallation Type Advantages ConsiderationsVision 110 Lens Options and Throw Ratios Ceiling Installation Floor InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Vision 110 Vertical and Horizontal Lens Shift Limits Folded OpticsInstalling the Primary Projection Lens Disconnection or lens damage Installing the Optional CineWide Lens Mount 6shows the Vision 110/CineWide with AutoScope motor assembly Remove Vision 110 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 110/CineWide Adjusting the Projection Mounting the VisionFloor Mounting Upright Ceiling Mounting Inverted AngleConnecting Source Connections to the VisionHdmi Connections See Figure 11011. Digital DTV RGB or Component Video Connections HD1, HD2 12. Digital DTV RGB or Component Video Connections HD3 DTV or Progressive Component YPbPr SourceAnalog Computer RGB Connections See Figure 13. Analog RGB ConnectionsVideo/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnection 15. RS-232 Control System ConnectionRear Panel Connecting 12-volt Trigger Outputs to External EquipmentAutoScope Lens Motor Rear Connecting an External IR Power sourceReceiver to the Vision Rear PanelTurning on the Power Adjusting the Picture OrientationZoom Primary Lens AdjustmentsFocus Installing and Adjusting the CineWide Anamorphic Lens Primary lens is perfectly centered on the screen19. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Using the On-Screen Menus 4OperationMemory Presets ServiceInput Source Aspect RatioAspect Ratio Main MenuInput Source Aspect Ratio Settings Description169 Hdtv programs in their nativePicture PicturePerform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionMemory Presets Memory PresetsInformation InformationISF Day CalibrationCalibration ISF Night OSD Position To adjust the menu and press Enter or Gain/Offset Refer to ISF Night Display Color, aboveHD Format ServiceService Presets 5Maintenance and Troubleshooting Lamp ReplacementFilter Replacement Symptom Possible Causes Troubleshooting TipsTroubleshooting Chart Maintenance and Troubleshooting 6Serial Communications Serial Command SyntaxRS-232 Connection and Port Configuration Serial Commands and Responses Command Description ResponseInput Selection Commands Aspect Ratio CommandsCommand Description Response Image Preset Commands Menu Navigation CommandsPicture Adjust Commands Enter or Select buttonSerial Communications 7Specifications Vision 110 SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsVision 110 Dimensions Vision 110/CineWide with AutoScope DimensionsSupported Signal Timings by Input Supported TimingsFormat Resolution Frequency HD 1/HD 2/HD Specifications Page Vidikron