Vidikron Vision 110 operation manual Filter Replacement

Page 74

Maintenance and Troubleshooting

6.Install the new lamp module.

7.Replace the lamp cover and re-tighten all screws.

5.2

Filter Replacement

Whenever you replace the lamp – or more often if the projector is installed in an extremely dusty environment – you should also replace the filter located at the right side of the projector.

1.Loosen the two screws holding the filter access panel in place. Then, remove the panel.

2.Pull the filter out of the projector and discard. Do not reuse filters.

3.Insert the new filter with the pleats facing in and the foam-covered side facing out.

4.Replace the filter access panel and tighten the screws to secure it.

Side Filter

Access

Panel

60	Vidikron Vision Model 110 Installation/Operation Manual

Image 74

Contents 110 Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Important Safety Instructions Compliance Information Declaration of ConformityFCC Part 1Table of Contents Attach Lens Mounting Assembly to Lens Motor Carriage Plate OperationMaintenance and Troubleshooting Table of Contents Xii 1List of Figures List of Figures Xiv 1Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Vision 110 offers these key features and benefitsOptional Accessories Controls and Functions Vision 110 at a GlanceVision 110 Rear Panel Vision 110 Rear PanelSTAND-BY LED RS-232/485 Control Port Vision 110 Rear Connector PanelService only For future use Volt 750 mA Trigger OutputsHdmi I 1 / Hdmi II 2 Digital HD3 InputVision 110 Remote Control Vision 110 Remote ControlSource Selection Buttons Picture Adjustment Buttons BRT BrightnessOn / OFF VID S-Video169 Memory Preset ButtonsAspect Ratio Selection Buttons Lbox LetterboxOperation 3InstallationRemote Control Step Procedure For Details, Refer to Quick SetupInstallation Overview If installing a Vision 110/CineWide or VisionInstallation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsVision 110 Lens Options and Throw Ratios Vertical and Horizontal Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Example only Vision 110 Vertical and Horizontal Lens Shift Limits Folded OpticsInstalling the Primary Projection Lens Disconnection or lens damage Installing the Optional CineWide Lens Mount 6shows the Vision 110/CineWide with AutoScope motor assembly Remove Vision 110 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 110/CineWide Floor Mounting Upright Ceiling Mounting Inverted Adjusting the ProjectionMounting the Vision AngleHdmi Connections See Figure Connecting SourceConnections to the Vision 11011. Digital DTV RGB or Component Video Connections HD1, HD2 12. Digital DTV RGB or Component Video Connections HD3 DTV or Progressive Component YPbPr SourceAnalog Computer RGB Connections See Figure 13. Analog RGB ConnectionsVideo/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnection 15. RS-232 Control System ConnectionRear Panel Connecting 12-volt Trigger Outputs to External EquipmentAutoScope Lens Motor Rear Receiver to the Vision Connecting an External IRPower source Rear PanelTurning on the Power Adjusting the Picture OrientationZoom Primary Lens AdjustmentsFocus Installing and Adjusting the CineWide Anamorphic Lens Primary lens is perfectly centered on the screen19. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Using the On-Screen Menus 4OperationInput Source Memory PresetsService Aspect RatioAspect Ratio Main MenuInput Source 169 Aspect Ratio SettingsDescription Hdtv programs in their nativePicture PicturePerform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionInformation Memory PresetsMemory Presets InformationISF Day CalibrationCalibration ISF Night OSD Position To adjust the menu and press Enter or Gain/Offset Refer to ISF Night Display Color, aboveHD Format ServiceService Presets 5Maintenance and Troubleshooting Lamp ReplacementFilter Replacement Symptom Possible Causes Troubleshooting TipsTroubleshooting Chart Maintenance and Troubleshooting 6Serial Communications Serial Command SyntaxRS-232 Connection and Port Configuration Input Selection Commands Serial Commands and ResponsesCommand Description Response Aspect Ratio CommandsPicture Adjust Commands Command Description Response Image Preset CommandsMenu Navigation Commands Enter or Select buttonSerial Communications 7Specifications Vision 110 SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsVision 110 Dimensions Vision 110/CineWide with AutoScope DimensionsSupported Signal Timings by Input Supported TimingsFormat Resolution Frequency HD 1/HD 2/HD Specifications Page Vidikron