Vidikron Vision 110 operation manual Stand-By Led

Page 21

Controls and Functions

5.LEFT BUTTON

Used to direct-select inputs or move the menu cursor left in the OSD. When no menu is present on-screen, the LEFT button toggles through the different sources, in this order: HDMI 2 - HDMI 1 - HD3 (VGA/Y-Pb-Pr) - HD 2 (BNC) - HD 1 (RCA) - S-Video - Composite (VID)

6.UP BUTTON

Use to direct-select aspect ratios or move the menu cursor up in the OSD. When no menu is present on-screen, the UP button toggles through aspect ratios in the following order:

16:9 - 4:3 - Letterbox - IntelliWide - Cinema - IntelliWide 2.35

(IntelliWide 2.35 is available only on CineWide-equipped projectors. For more information about aspect ratios, refer to Table 4-1.)

7.DOWN BUTTON

Use to direct-select aspect ratios or move the menu cursor down in the OSD. When no menu is present on-screen, the DOWN button toggles through the different aspect ratios, in this order:

IntelliWide 2.35 - Cinema - IntelliWide - Letterbox - 4:3 - 16:9

8. RIGHT BUTTON

Used to direct-select inputs or move the menu cursor right in the OSD. When no menu is present on-screen, the RIGHT button toggles through the different sources, in this order: Composite (VID) - S-Video - HD 1 (RCA) - HD 2 (BNC) - HD 3 (VGA/Y-Pb-Pr) - HDMI 1 - HDMI 2

9.STAND-BY LED

Lights orange to indicate that the projector is in standby mode.

10.SOFT POWER BUTTON

Press once to turn on the Vision 110. Press it again to put the projector into Standby mode. For a discrete on or off command, you can use the direct access buttons on the remote control (see Figure 2-4).

11.PATTERN BUTTON

Press PATTERN to access the internal test pattern menu. Use arrow keys to select a pattern and press SELECT to confirm. Press PATTERN again to return to the selected source.

12.POWER INPUT (100 to 240 VAC) Connect the Vision 110 to power here.

13.SERVICE PORT

For use by authorized service personnel only.

14.SELECT BUTTON

Press SELECT to confirm your selection of a highlighted choice on the On-Screen Display (OSD).

15.MENU BUTTON

Pressing the MENU button brings up the main Vision 110 menu. Also, if you are in an adjustment mode or function, pressing MENU brings the menu back one level.

16.INPUTS

Connect your video sources and other equipment to these inputs. Refer to Vision 110 Rear Connector Panel on page 8.

Vidikron Vision Model 110 Installation/Operation Manual

7

Image 21

Contents 110 Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part 1Table of Contents Operation Attach Lens Mounting Assembly to Lens Motor Carriage PlateMaintenance and Troubleshooting Table of Contents Xii 1List of Figures List of Figures Xiv About This Manual 1IntroductionIf you need Turn to Using This ManualVision 110 offers these key features and benefits Description, Features and BenefitsOptional Accessories Vision 110 at a Glance Controls and FunctionsVision 110 Rear Panel Vision 110 Rear PanelSTAND-BY LED Service only For future use Vision 110 Rear Connector PanelRS-232/485 Control Port Volt 750 mA Trigger OutputsHD3 Input Hdmi I 1 / Hdmi II 2 DigitalVision 110 Remote Control Vision 110 Remote ControlOn / OFF Picture Adjustment Buttons BRT BrightnessSource Selection Buttons VID S-VideoAspect Ratio Selection Buttons Memory Preset Buttons169 Lbox Letterbox3Installation Remote ControlOperation Installation Overview Quick SetupStep Procedure For Details, Refer to If installing a Vision 110/CineWide or VisionProjector Installation Options Installation ConsiderationsInstallation Type Advantages ConsiderationsVision 110 Lens Options and Throw Ratios Floor Installation Ceiling InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Folded Optics Vision 110 Vertical and Horizontal Lens Shift LimitsInstalling the Primary Projection Lens Disconnection or lens damage Installing the Optional CineWide Lens Mount 6shows the Vision 110/CineWide with AutoScope motor assembly Remove Vision 110 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 110/CineWide Mounting the Vision Adjusting the ProjectionFloor Mounting Upright Ceiling Mounting Inverted AngleConnections to the Vision Connecting SourceHdmi Connections See Figure 11011. Digital DTV RGB or Component Video Connections HD1, HD2 DTV or Progressive Component YPbPr Source 12. Digital DTV RGB or Component Video Connections HD313. Analog RGB Connections Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Video/Composite Video Connections See Figure15. RS-232 Control System Connection ConnectionConnecting 12-volt Trigger Outputs to External Equipment AutoScope Lens Motor RearRear Panel Power source Connecting an External IRReceiver to the Vision Rear PanelAdjusting the Picture Orientation Turning on the PowerPrimary Lens Adjustments FocusZoom Primary lens is perfectly centered on the screen Installing and Adjusting the CineWide Anamorphic Lens19. Attaching the Anamorphic Lens to the Lens Adapter Ring Adjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry 4Operation Using the On-Screen MenusService Memory PresetsInput Source Aspect RatioMain Menu Input SourceAspect Ratio Description Aspect Ratio Settings169 Hdtv programs in their nativePicture PictureTypical Pluge Pattern for Adjusting Brightness Perform the adjustments in the order listed hereGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionMemory Presets Memory PresetsInformation InformationCalibration Calibration ISF NightISF Day Gain/Offset Refer to ISF Night Display Color, above OSD Position To adjust the menu and press Enter orService ServiceHD Format Presets Lamp Replacement 5Maintenance and TroubleshootingFilter Replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port Configuration6Serial Communications Command Description Response Serial Commands and ResponsesInput Selection Commands Aspect Ratio CommandsMenu Navigation Commands Command Description Response Image Preset CommandsPicture Adjust Commands Enter or Select buttonSerial Communications Vision 110 Specifications 7SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements DimensionsVision 110/CineWide with AutoScope Dimensions Vision 110 DimensionsSupported Timings Supported Signal Timings by InputFormat Resolution Frequency HD 1/HD 2/HD Specifications Page Vidikron