Variance from Country to Country

Motorola T2-2500, 45101 manual Variance from Country to Country

Page 22

WallPlate Installation

Installation 2: Install over European wall plate with 65mm offset

The European style wall plate is comprised of four primary parts; the box, the modular connector, mounting bracket for the modular connector, and the outer plastic cover. The decorative plastic cover can be discarded and replaced by the m2a WallPlate.

1.Typical dimensions of the telco box are 70mm square; 85mm square, or 90mm square with a 65mm mounting screw offset.

2.Existing mounting screws are typically 5mm to 10mm. Check local machine screw dimensions and thread style when planning the installation. Typical required length is 10mm to 20mm. Replacement machine screws should be obtained locally prior to the installation.

Step 1: Remove and discard cover over existing wall plate

3.Remove plastic cover and expose RJ11 bracket and mounting screws

4.Remove mounting screws

5.Align bracket horizontal slots over 65mm offset mounting holes

6.Install mounting screws (replace with 20mm machine screws if necessary)

Step 2: Install RJ11 line cable

7.Connect short RJ11 pigtail cable to internal RJ11 connector on the m2a circuit board

8.Connect other side of RJ11 pigtail cable to RJ11 connector on the RJ11 wall plate

Step 3: Attach cover to the bracket

9.Use a slight angle to align the bottom connector.

10.Apply firm pressure to the top and bottom of cover to snap the connectors in place.

11.Install two (2) set screws in the pre-drilled holes in the top of the cover.

Motorola, Inc.	549453-001-00-a	Page 22 of 51

Image 22

Contents

Aka mT2a EthernetXD Page Regulatory Statements Model Number45125 MT2a Switch M2 WallPlateWaste Electrical and Electronic Equipment Weee Commands and Syntax Quality of Service QoS Administrative Commands Commands and SyntaxCommand Hierarchy Show CommandsStyle Conventions Command DescriptionCommand Completion Interface RangeModel Numbers and Description HardwareModel Number Switch Rear Panel Connections Switch Front Panel ConnectionsMounting Options M2a 2 port WallPlate M4a 4 port Service UnitWallPlate M4a 4 port WallPlateCLI Configuration Script files System AdministrationManagement Access Access MethodsConfiguration Files using the webUI File dirLine Quality Http MenusUpgrading the System Image System Menu Interface Menu Advanced Menu Monitor MenuCommit mode View System Configuration and StatusSummary Startup Running Other Configuration Help Reset to Default ConfigurationSystem config mode automanualmode Access Control Lists ACLs Ip access-list config 1 deny httpRadius network authenticated login Mounting options for existing telco box WallPlate InstallationInstallation Guidelines Other mounting optionsInstall RJ11 line cable Installation 1 Install over 70mm x 114mm wall plateInstall bracket over existing wall plate Attach cover to the bracketVariance from Country to Country Remove and discard cover over existing wall plateConnect RJ11 cable Installation 3 External mounting tabsRemove the cover to service the WallPlate Assemble the m2 WallPlateInstall cross connects Installation StepsInstall mT2 switch in phone room MDF or IDF Review the cross-connectsConfigure mT2 EthernetXD Switch Components provided with the m2a WallPlate In-Room InstallationTools Required Components required to purchaseStep Determine which port is being installed Enable line powerFinish the installation Enable line powerVlan terminology Vlan Specification802.1Q VLANs Tagged UntaggedVlan commands in mT2 Tag-based Vlan Mode Port-based Vlan ModeWeb UI configuration Vlan General webUISet Vlan Egress Rules Tag-based Vlan webUICreate/Delete VLANs Set Vlan Ingress RulesPort-based Vlan webUI Quality of Service QoS QoS commands and conceptsNetwork qos interface queue interface-id mode mode 802.1P bit Dynamic packet classificationQueue Packet Classification CommandsQoS Example Packet transmissionVlan Tutorials Tutorial 1 Simple Hotel configurationThird party network configuration Privacy and QoS in this networkTutorial 2 Mixed Mode Vlan configuration with QoS This networkEnable and create VLANs, Enable QoS Tutorial 3 Per port 802.1Q VLANs VLAN-Ids used in this configurationPort Enable VLANs, configure PVIDs Convert this tutorial to a real-world configurationEth1 Eth2 Port SwitchEth1 Eth2 Port Motorola, Inc 549453-001-00-a Enable VLANs, configure Vlan modes Optional configuration on the cascaded switchLine Status Line Current Watts ReferenceAppendix a Pin-out Assignments RJ21 Line ConnectorsRS-232 console port Gigabit Ethernet ports Fast Ethernet WallPlate portsMT2 Switch Appendix B Hardware SpecificationsM2 WallPlate Page FCC Part 15A Important Safety Instructions mT2a SwitchAppendix C Compliance M2a WallPlate

Motorola T2-2500, 45101 manual Variance from Country to Country