Motorola T2-2500 In-Room Installation, Tools Required, Components provided with the m2a WallPlate

Page 26

Installation Steps

In-Room Installation

Note: These instructions follow the Installation 1 procedure from the previous chapter. Please consult WallPlate Installation for variations of the installation routine.

Tools Required:

Number 2 Philips head screwdriver

Number 2 flat blade screwdriver

Components provided with the m2a WallPlate:

1 – m2a WallPlate bracket and cover with circuit board 1 – 150mm (6”) RJ11 pigtail cable

1 – RJ11 blanking plug

2 – Number 6 oval head screws, 0.25”

Components required to purchase:

Regulated 12V power supply. Use of the wrong power supply could result in damage to your WallPlate unit. Please order a small quantity of regulated 12V power supplies from Motorola PBN to use during installation.

If you do not have the correct regulated 12V power supply – STOP. Order a regulated 12V power supply from your Motorola PBN sales representative.

Step 1

1.Loosen screws on wall plate approximately 6mm (1/4”)

2.Attach the bracket using the keyhole slots

3.Tighten screws until the bracket is firmly attached, do not over tighten

Step 2

Connect 150mm (6”) cable (supplied) between m2a circuit board and existing RJ11 jack.

Motorola, Inc.

549453-001-00-a

Page 26 of 51

 

 

 

Page 25 Page 27
Image 26
Page 25 Page 27
Contents
Aka mT2a EthernetXD Page Regulatory Statements Model Number45125 MT2a Switch M2 WallPlateWaste Electrical and Electronic Equipment Weee Commands and Syntax Quality of Service QoS Administrative Commands Commands and SyntaxCommand Hierarchy Show CommandsStyle Conventions Command DescriptionCommand Completion Interface RangeModel Number HardwareModel Numbers and Description Mounting Options Switch Front Panel ConnectionsSwitch Rear Panel Connections M2a 2 port WallPlate M4a 4 port Service UnitWallPlate M4a 4 port WallPlateCLI Configuration Script files System AdministrationManagement Access Access MethodsConfiguration Files using the webUI File dirLine Quality Http MenusUpgrading the System Image System Menu Interface Menu Advanced Menu Monitor MenuSummary Startup Running View System Configuration and StatusCommit mode System config mode automanualmode Reset to Default ConfigurationOther Configuration Help Access Control Lists ACLs Ip access-list config 1 deny httpRadius network authenticated login Mounting options for existing telco box WallPlate InstallationInstallation Guidelines Other mounting optionsInstall RJ11 line cable Installation 1 Install over 70mm x 114mm wall plateInstall bracket over existing wall plate Attach cover to the bracket Variance from Country to Country Remove and discard cover over existing wall plateConnect RJ11 cable Installation 3 External mounting tabsRemove the cover to service the WallPlate Assemble the m2 WallPlateInstall cross connects Installation StepsInstall mT2 switch in phone room MDF or IDF Review the cross-connectsConfigure mT2 EthernetXD Switch Components provided with the m2a WallPlate In-Room InstallationTools Required Components required to purchaseStep Determine which port is being installed Enable line powerFinish the installation Enable line powerVlan terminology Vlan Specification802.1Q VLANs Tagged UntaggedVlan commands in mT2 Tag-based Vlan Mode Port-based Vlan ModeWeb UI configuration Vlan General webUISet Vlan Egress Rules Tag-based Vlan webUICreate/Delete VLANs Set Vlan Ingress RulesPort-based Vlan webUI Quality of Service QoS QoS commands and conceptsNetwork qos interface queue interface-id mode mode Queue Dynamic packet classification802.1P bit Packet Classification CommandsQoS Example Packet transmissionVlan Tutorials Tutorial 1 Simple Hotel configurationThird party network configuration Privacy and QoS in this networkTutorial 2 Mixed Mode Vlan configuration with QoS This networkEnable and create VLANs, Enable QoS Port VLAN-Ids used in this configurationTutorial 3 Per port 802.1Q VLANs Enable VLANs, configure PVIDs Convert this tutorial to a real-world configurationEth1 Eth2 Port Motorola, Inc 549453-001-00-a SwitchEth1 Eth2 Port Enable VLANs, configure Vlan modes Optional configuration on the cascaded switchLine Status Line Current Watts ReferenceRS-232 console port RJ21 Line ConnectorsAppendix a Pin-out Assignments Gigabit Ethernet ports Fast Ethernet WallPlate portsM2 WallPlate Appendix B Hardware SpecificationsMT2 Switch Page FCC Part 15A Important Safety Instructions mT2a SwitchAppendix C Compliance M2a WallPlate
Top Page Image Contents