Motorola 45101, T2-2500 manual Reset to Default Configuration, Other Configuration Help

Page 17

System Administration

In manual mode, commands are executed immediately, but are not saved to memory. The commands will be lost when rebooted if they are not committed.

To change the mode:

system config mode <automanual(mode)>

To commit manual commands to memory:

system config commit

Reset to Default Configuration

From the CLI, enter the following command:

system config default

Note: This command is only available from a local serial login session.

Other Configuration Help

The mT2 Command Reference is the master text for all T2 configurations. It contains an alphabetical listing of all CLI commands, syntax and example configuration.

The web UI features a context-sensitive help system.

Motorola, Inc.

549453-001-00-a

Page 17 of 51

 

 

 

Page 16 Page 18
Image 17
Page 16 Page 18
Contents
Aka mT2a EthernetXD Page Regulatory Statements Model Number45125 M2 WallPlate MT2a SwitchWaste Electrical and Electronic Equipment Weee Commands and Syntax Quality of Service QoS Command Hierarchy Commands and SyntaxAdministrative Commands Show CommandsCommand Completion Command DescriptionStyle Conventions Interface RangeModel Number HardwareModel Numbers and Description Mounting Options Switch Front Panel ConnectionsSwitch Rear Panel Connections WallPlate M4a 4 port Service UnitM2a 2 port WallPlate M4a 4 port WallPlate Management Access System Administration CLI Configuration Script files Access MethodsFile dir Configuration Files using the webUIUpgrading the System Image Http MenusLine Quality System Menu Interface Menu Advanced Menu Monitor MenuSummary Startup Running View System Configuration and StatusCommit mode System config mode automanualmode Reset to Default ConfigurationOther Configuration Help Ip access-list config 1 deny http Access Control Lists ACLsRadius network authenticated login Installation Guidelines WallPlate InstallationMounting options for existing telco box Other mounting optionsInstall bracket over existing wall plate Installation 1 Install over 70mm x 114mm wall plateInstall RJ11 line cable Attach cover to the bracketRemove and discard cover over existing wall plate Variance from Country to CountryRemove the cover to service the WallPlate Installation 3 External mounting tabsConnect RJ11 cable Assemble the m2 WallPlateInstall mT2 switch in phone room MDF or IDF Installation StepsInstall cross connects Review the cross-connectsConfigure mT2 EthernetXD Switch Tools Required In-Room InstallationComponents provided with the m2a WallPlate Components required to purchaseStep Finish the installation Enable line powerDetermine which port is being installed Enable line power802.1Q VLANs Vlan SpecificationVlan terminology Tagged UntaggedTag-based Vlan Mode Port-based Vlan Mode Vlan commands in mT2Vlan General webUI Web UI configurationCreate/Delete VLANs Tag-based Vlan webUISet Vlan Egress Rules Set Vlan Ingress RulesPort-based Vlan webUI QoS commands and concepts Quality of Service QoSNetwork qos interface queue interface-id mode mode Queue Dynamic packet classification802.1P bit QoS Example CommandsPacket Classification Packet transmissionThird party network configuration Tutorial 1 Simple Hotel configurationVlan Tutorials Privacy and QoS in this networkThis network Tutorial 2 Mixed Mode Vlan configuration with QoSEnable and create VLANs, Enable QoS Port VLAN-Ids used in this configurationTutorial 3 Per port 802.1Q VLANs Convert this tutorial to a real-world configuration Enable VLANs, configure PVIDsEth1 Eth2 Port Motorola, Inc 549453-001-00-a SwitchEth1 Eth2 Port Optional configuration on the cascaded switch Enable VLANs, configure Vlan modesLine Status Watts Reference Line CurrentRS-232 console port RJ21 Line ConnectorsAppendix a Pin-out Assignments Fast Ethernet WallPlate ports Gigabit Ethernet portsM2 WallPlate Appendix B Hardware SpecificationsMT2 Switch Page Appendix C Compliance Important Safety Instructions mT2a SwitchFCC Part 15A M2a WallPlate
Top Page Image Contents