Alcatel-Lucent 6850, 9000, 6800 user manual Pim

Page 71

Open Problem Reports and Feature Exceptions

PR 105491

Existing inter-area-prefix and inter-area-router LSAs are not originated into areas that are created after initial convergence of the network on an OS9000. For example, the router is running and it originates a set of inter-area-prefix or inter-area-router LSAs into all known areas. Later, another area is added, the new area will not have any of the inter-area-prefix or inter-area-router LSAs that exist in the other areas prior to the creation of the new area.

Workaround: When adding an area to OSPFv3 after it has been running for a while, it should be globally disabled and then re-enabled using the "ipv6 ospf status disable/enable" command.

PR 105770

Point-to-point interfaces are not supported in OSPFv3 at this time; therefore, 6to4 tunnels cannot be used with OSPFv3.

Workaround: There is no known workaround at this time.

PR 107353

OSPFv3 will leak memory in either of the following two cases on an OS9000: 1) During SPF runs. 2) During adjacency formation.

Workaround: There is no workaround that will eliminate this leak. However, it's effect can be somewhat mitigated by trying to minimize the causal events (namely SPF calculations and new adjacency forma- tions) between reboots.

PIM

Problem Reports

PR 102501

Currently, there is no support for an "ip unload" command. This can be a problem for customers who have loaded a DRC loadable module and executed a "write memory" command to update the boot.cfg file. Then decided that they wanted the module permanently removed.

Workaround: To permanently disable a module, execute the module's "disable" command followed by another "write memory" command and a reboot. To also free up any memory possibly used by the disabled module, edit the boot.cfg file using the "vi" command to delete the "ip load <module>" command along with any non-default configuration lines associated with the module.

OmniSwitch 6800/6850/9000—Release 6.1.3.R01

page 71

Image 71

Contents Page Related Documentation OmniSwitch 6800 Series Getting Started guideUpgrade Instructions for 6.1.3.R01 Memory Requirements OmniSwitch 6800 SeriesOmniSwitch 6850 Series OmniSwitch 9000 SeriesNew Hardware Supported OS9800-CMM New Chassis Management Module CMMDual Speed Ethernet Transceivers OmniSwitch 9000 OS-IP-SHELF PoE Power ShelfOmniSwitch 9600 Support for PS-510W AC/PS-360W AC Gigabit Ethernet Transceiver SFP MSA100FX Ethernet Transceivers 3.R01 Supported Hardware/Software CombinationsModule Type Part Number Asic Physical Feature Platform Software Package New Software FeaturesVlan Range Support BGP4 Software SupportedPIM-SM 802.1Q 2005 Mstp 802.1W Rstp Default802.1x Device Classification Access Guardian 802.1QSource ipv6 destination ipv6 ipv6 Nh next header flow-label Access Control Lists ACLsAccess Control Lists ACLs for IPv6 ACL & Layer 3 SecurityACL Manager Automatic Vlan Containment AVC Authenticated Switch AccessAuthenticated VLANs BGP Graceful Restart Basic IPv4 RoutingDhcp Option-82 Relay Agent Information Option Command Line Interface CLIBpdu Shutdown Ports Dhcp RelayEnd User Partitioning Eupm DNS ClientDynamic Vlan Assignment Mobility Health Statistics HTTP/HTTPS Port ConfigurationEthernet Interfaces Generic UDP RelayIP DoS Enhancements Interswitch Protocol AmapIP Multicast Switching Ipms IPv6 NPD IP Multicast Switching Ipms ProxyingIP Route Map Redistribution L2 Static Multicast Addresses IPX RoutingL2 Dhcp Snooping L2 MAC Address Table Size EnhancementMulticast Routing Learned Port Security LPSLink Aggregation static & 802.3ad OSPFv2/OSPFv3 MultinettingNTP Client Policy Server Management Partitioned Switch ManagementPolicy Based Routing Permanent Mode Per-VLAN Dhcp RelayPort Mirroring Power over Ethernet PoEQuality of Service QoS Port MappingRouting Protocol Preference Redirect Policies Port and Link AggregateRouter Discovery Protocol RDP SSH Software Supported Operating Systems Secure Shell SSH Public Key AuthenticationSecure Copy SCP Secure Shell SSHSFlow Smart Continuous Switching OmniSwitch 6800/OmniSwitchSmart Continuous Switching OmniSwitch Server Load Balancing SLBSoftware Rollback Source LearningSyslog to Multiple Hosts Switch LoggingText File Configuration Spanning TreeVRRPv2/VRRPv3 User Definable Loopback InterfaceVlan Range Support Vlan Stacking and TranslationWeb-Based Management WebView Trap Name Platforms Description Supported TrapsTrap Name Platforms Description Sion which was active on a slot cannot Trap Name Platforms Description Table gets dropped due to the overload Software Feature Unsupported CLI Commands Unsupported Software FeaturesUnsupported CLI Commands RIP Alcatel IND1LAG Unsupported MIBsMIB Name Unsupported MIB variables Alcatel IND1AAA Alcatel IND1BgpAlcatelIND1Slb MIB Name Unsupported MIB variables AlcatelIND1QoSAlcatelIND1VlanManager MIB Name Unsupported MIB variablesIetfsnmp Problem Reports Open Problem Reports and Feature ExceptionsCommand Line Interface CLI SFlow RmonWeb-Based Management WebView Feature ExceptionsOpen Problem Reports and Feature Exceptions Open Problem Reports and Feature Exceptions Autonegotiation LayerBridging Ethernet Interfaces Open Problem Reports and Feature Exceptions Group Mobility IP Multicast Switching IpmsPort Mirroring/Monitoring Link AggregationSource Learning Open Problem Reports and Feature Exceptions Open Problem Reports and Feature Exceptions Spanning Tree Open Problem Reports and Feature Exceptions Vlan Stacking Dhcp Snooping Basic IP RoutingIPv6 Open Problem Reports and Feature Exceptions UDP Relay Server Load Balancing SLBAdvanced Routing OSPFv3 DvmrpPIM General Quality of Service includes ACLsPolicy Manager Security 802.1x Authenticated Switch Access Policy Server Management Authenticated VLANsSystem Open Problem Reports and Feature Exceptions Chassis Supervision Open Problem Reports and Feature Exceptions Power Over Ethernet Open Problem Reports and Feature Exceptions Redundancy / Hot Swap Hot Swap Time Limitations for OmniSwitchOpen Problem Reports and Feature Exceptions Region Phone Number Technical Support