Alcatel-Lucent 6600 Series, 6648, 6624 manual Serial Connection to the Console Port

Page 71

OmniSwitch 6600 Series Chassis and Hardware Components

Console Port

 

 

 

 

Console Port

Serial Connection to the Console Port

The console port, located on the chassis front panel, provides a serial connection to the switch and is required when logging into the switch for the first time (refer to the OmniSwitch 6600 Series Getting Started Guide for more information). By default, this connector (a female DB-9 on OmniSwitch 6624 and 6648 switches and an RJ-45 port on OmniSwitch 6600-U24 switches) provides a DCE console connec- tion.

Serial Connection Default Settings

The factory default settings for the serial connection are as follows:

baud rate

9600

 

 

parity

none

 

 

data bits (word size)

8

 

 

stop bits

1

 

 

Modifying the Serial Connection Settings

If you wish to modify the default serial connection settings (i.e., baud rate, parity, data bits, and stop bits), refer to the following steps.

Note. You must be connected to the switch via the console port before attempting to change serial connec- tion settings. Otherwise, an error message will display. In addition, if you are changing console port settings for switches in a stack, console port settings must be identical on all switches. Before configuring the console port settings for a stack, make sure each switch is operating in either primary or secondary status (you may be required to disconnect switches within the stack before beginning).

1Enter modify boot parameters at the CLI prompt. The boot prompt displays:

Boot >

2To change the baud rate, enter boot serialbaudrate, followed by the desired baud rate value. Options include 1200, 2400, 4800, 9600 (default), 19200, 38400, 57600, 76800, and 115200. For example:

Boot > boot serialbaudrate 19200

Note. Setting the console port to speeds above 9600 baud can cause problems with Zmodem uploads.

3To change the parity value, enter boot serialparity, followed by the desired parity value. Options include none (default), even, and odd. For example:

Boot > boot serialparity even

OmniSwitch 6600 Series Hardware Users Guide April 2004

page 2-51

Image 71
Contents OmniSwitch 6624/6648 Hardware Users Guide OmniSwitch 6600 Series Hardware Users Guide April Contents Contents Blank Cover Panels Index-1 Unsupported Platforms Supported PlatformsWho Should Read this Manual? When Should I Read this Manual?What is in this Manual? What is Not in this Manual?Documentation Roadmap Stage 1 Using the Switch for the First TimeStage 2 Gaining Familiarity with Basic Switch Functions How is the Information Organized?Anytime Stage 3 Integrating the Switch Into a NetworkRelated Documentation OmniSwitch 6600 Series Getting Started GuideTechnical Support OmniSwitch 6600 Series Stand-Alone Stand-Alone and Stacked ConfigurationsStacked Configurations Smart Continuous Switching Availability FeaturesAutomatic Monitoring Software RollbackHot Swapping Hardware MonitoringOS6624/6600-U24 Throughput OmniSwitch 6600 Series Fabric CapacitiesPort and Fabric Capacities User-Driven MonitoringSingle Office Building with 1000 Users Application ExamplesOmniPCX Medium Campus with 1500 UsersApplication Examples OmniSwitch 6600 Series Chassis and Hardware Components OmniSwitch 6600 Series Chassis and Hardware Components 10/100 Ethernet Ports OmniSwitchOmniSwitch 6624 Front Panel Console Port10/100 Ethernet Port Specifications OS6624 SpecificationsOmniSwitch 6600-U24 Console Port Gigabit Ethernet Uplink Module Slot OmniSwitch 6600-U24 Front PanelOS6600-U24 Specifications SFP Mbps Ethernet SFP Port SpecificationsTM OmniSwitch OmniSwitch 6648 Front PanelOS6648 Specifications Front Panel LED Descriptions OS6648 Shown Status LEDsRear Panel OmniSwitch 6600 Series Rear PanelRedundant Power Supply Bay Power Connector Socket Inline Power ConnectorAirflow Considerations Mounting the SwitchOmniSwitch 6600 Series Chassis Top View Installing the Switch on a Tabletop or Bench Installation OptionsAttaching a Rack-Mount Flange Attaching the Switch to the RackRack Mounting Stacked Configurations Grounding the Chassis Power CordsSpecifications Power Cord TypesBack Up Power Supply Specifications Back Up Power SupplyPower Supply Redundancy Back Up Power Supply Front PanelRedundant AC Circuit Recommendation OmniSwitch 6600 Series Redundant AC Circuit ExampleBack Up Factory-Installed Primary Power Supply AC Circuit Back Up Factory-Installed Primary Power SupplyHot Swapping Installing a Back Up Power SupplyOrienting the Back Up Power Supply Tightening the Captive Screws Inserting the Back Up Power SupplyLoosening the Captive Screws Removing a Back Up Power SupplyRemoving the Back Up Power Supply Blank Cover Panel Requirement Viewing Primary and Back Up Power Supply StatusNo Slot Number is Specified Viewing Power Supply Status for Stacked ConfigurationsSlot Number is Specified MiniGBIC Slots Gigabit Ethernet Uplink ModulesOS6600-GNI-U2 OS6600-GNI-U2 Gigabit Ethernet Uplink Front PanelOS6600-GNI-U2 Uplink Module Specifications Copper Gigabit Ethernet Ports OS6600-GNI-C2 Uplink Module SpecificationsOS6600-GNI-C2 OS6600-GNI-C2 Gigabit Ethernet Uplink Front PanelStacking Module Front Panel Stacking Module SpecificationsHssdc Stacking Connectors Stacking ModuleInserting the Uplink or Stacking Module Installing Uplink and Stacking ModulesInstalling Uplink and Stacking Modules Removing Uplink and Stacking Modules Removing the Module Mini Gigabit Interface Converter MiniGBIC Mini Gigabit Interface Converters MiniGBICsMiniGBIC-LH-70 Technical Specifications MiniGBIC SpecificationsMiniGBIC-SX Technical Specifications MiniGBIC-LX Technical SpecificationsInserting the MiniGBIC OS6648 Shown Installing MiniGBICsRemoving MiniGBICs Installed MiniGBIC OS6648 ShownSFP Module Mbps SFPs OS6600-U24SFP-100-LC-SM40 Technical Specifications Mbps SFP SpecificationsSFP-100-LC-MM Technical Specifications SFP-100-LC-SM15 Technical SpecificationsMtrj SFP-100-MTRJ-MM Technical SpecificationsInserting the SFP Installing SFPs OS6600-U24Removing SFPs OS6600-U24 Viewing Chassis Temperature Status Temperature ManagementViewing Temperature Status for Stacked Configurations Temperature Errors Viewing Fan Status Viewing Fan Status for Stacked ConfigurationsNo Slot Number is Specified Air Exhaust. The airflow Chassis AirflowRight Side Air Intake Vent Left Side Fan Exhaust VentsEffects of Missing Blank Panels on Chassis Airflow Blank Cover PanelsCopper Gigabit Ethernet Port RJ-45 Pinout RS232 Console Port Female DB9 Connector PinoutPinouts 10/100 Ethernet Port RJ-45 PinoutTXD RJ-45 Console Port Connector PinoutSerial Connection to the Console Port Serial Connection Default SettingsModifying the Serial Connection Settings Console PortAdditional table output not shown Hardware Information Viewing Basic Chassis InformationSlot and Component Information Detailed Slot and Component Information Power onGbic IBM Basic Primary Slot and Component Information Basic Chassis Information MAC Range Guidelines Managing MAC Addresses on the SwitchOmniSwitch 6600 Series MAC Range Specifications Viewing the Base Chassis MAC Address Determining Current MAC Address Allocation on the SwitchBase Chassis MAC Address in Stacked Configurations Base Chassis MAC Address as Unique IdentifierThis Chapter Managing OmniSwitch 6600 Series StacksParameter Description Configuration Steps Default Value Specifications and Default ValuesStack Overview Stack Composed of Four OmniSwitch 6648 SwitchesSlot Numbers within a Stack Stacking Resiliency and RedundancyCMM Role Redundancy CMM Roles in a StackFile Management Commands Switch PrimaryCMM Commands Chassis Management and Monitoring CommandsMemory Monitoring Commands Switch Logging and Monitoring CommandsAssigning Slot Numbers Setting Up a Stacked ConfigurationSEL Button Location Continue to Connecting Cables to Stacking Ports onValid Slot Assignments Stack of Four Switches with Unique Slot NumbersSlot Numbering Example Attaching the Stacking Cable to a Stacking Port Connecting Cables to Stacking PortsRecommended Redundant Connection Between Switches Connecting the Switches in the StackNo Connection Failure Connection Failure Between Switches 1Redundant Stack Connection Stacking Cable Redundancy ExampleVerifying Primary and Secondary Status for the Stack Booting the StackVerifying Slot Number Assignments Idle Status Reloading the Switch with the Secondary CMM Role Managing Switches in a StackReloading a Switch with a Primary or Secondary CMM Role Reloading the Switch with the Primary CMM RoleRestoring Switch Redundancy Synchronizing Switches in a StackModule Behavior During Takeover Changing the Secondary CMM Role to PrimaryResetting All Switches in a Stack Monitoring Stack Topology Managing and Monitoring OmniSwitch 6600 Series StacksMonitoring Stacks Secondary Active Monitoring Stacks Declaration of Conformity CE Mark Regulatory Compliance and Safety InformationEMC Standards Safety StandardsSafety and Environmental Standards Standards ComplianceCISPR22 Class a warning FCC Class A, PartCanada Class a Statement Class a Warning for Taiwan and Other Chinese Markets VcciElectrical Storm Warning Translated Safety WarningsChassis Lifting Warning Blank Panels WarningInvisible Laser Radiation Warning Installation WarningOperating Voltage Warning Lithium Battery WarningProper Earthing Requirement Warning Power Disconnection WarningRestricted Access Location Warning Read Important Safety Information WarningWrist Strap Warning Numerics Commit file commandCommit system command Copy flash-synchro commandTemp-threshold command Reload all command Reload commandShow chassis command Show cmm command Show fan command Takeover command