AMX NI-700/900 NI-700 Specifications, See the NI-700 On-Board Memory Specifications section on

Page 6

Introduction

NI-700 Specifications

Dimensions (HWD):

• 1.58" x 5.54" x 5.12" (4.01 cm x 14.10 cm x 13.00 cm)

 

• 1 RU (rack unit) high

 

 

Power Requirements:

• 280 mA @ 12 VDC

 

 

Memory:

See the NI-700On-Board Memory Specifications section on page 4.

 

 

Microprocessor:

• 304 MIPS

 

 

Weight:

• 1.30 lbs (0.59 kg)

 

 

Enclosure:

• Metal with black matte finish

 

 

Certifications:

• FCC Part 15 Class B, CE, and IEC 60950

 

 

Front Panel Components:

 

 

 

Program port

• RS-232 DB9 connector (male) can be connected to a DB9 port on a computer.

 

This port can be used with both Serial and NetLinx programming commands. It is

 

also used to both upload and download information from the NetLinx Studio 2.4

 

program.

 

 

Configuration DIP switch

• Sets the communication parameters for the Program port.

 

 

IR RX LED

• Red LED lights to when IR data is being received via the rear IR RX port.

 

 

IR LED

• Red LED lights during the transmission of IR or Serial data via the rear IR port.

 

 

I/O LEDs

• Four yellow LEDs light when the rear I/O channels 1-4 are active. LED indicator

 

for each I/O port reflects the state of that particular port.

 

 

Serial LEDs

• Two sets of red and yellow LEDs light when the rear DB9 Ports (1 & 2) are

 

transmitting or receiving RS-232, 422, or 485 data:

 

- TX LEDs (red) light when transmitting data

 

- RX LEDs (yellow) light when receiving data

 

- LED activity reflects transmission and reception activity

 

• These LEDs do not reflect changes in either the RTS or CTS when hardware

 

handshaking is used.

 

 

LINK/ACT

• Green LED lights when the Ethernet cable is connected and an active link is

 

established. This LED also blinks when receiving Ethernet data packets.

 

 

Status

• Green LED lights when the Controller is programmed and communicating

 

properly.

 

 

Output

• Red LED lights when the Controller transmits data, sets channels On/Off, sends

 

data strings, etc.

 

 

Input

• Yellow LED lights when the Controller receives data from button pushes, strings,

 

commands, channel levels, etc.

 

 

ID pushbutton

Provides the NetLinx ID (D:S) assignment for the device.

 

• The D notation is used to represent a device number.

 

• The S notation is used to represent the System number of the Master.

 

Refer to the NetLinx Integrated Controller WebConsole & Programming Guide for

 

details.

 

 

Rear Panel Connectors:

 

 

 

RS-232/422/485

• Two RS-232/422/485 control ports using DB9 (male) connectors with

(Ports 1 & 2)

XON/XOFF (transmit On/transmit Off), CTS/RTS (clear to send/ready to send),

 

and 300 - 115,200 baud.

 

• Channel range = 1 - 255

 

• Channels 1 - 254 provide feedback

 

• Channel 255 (CTS Push channel): Reflects the state of the CTS Input if a

 

'CTSPSH' command was sent to the port

 

• Output data format for each port is selected via software

 

• Two DB9 connectors provide RS-232/422/485 termination

 

 

2

NI-700 & NI-900 Hardware Reference Guide

Page 5 Page 7
Image 6
Page 5 Page 7
Contents NI-700/900 AMX Limited Warranty and Disclaimer Table of Contents Table of Contents NI-700 & NI-900 Hardware Reference Guide NI-700 Specifications NetLinx Integrated Master Controller FeaturesNI-700 Overview NI-700 Specifications See the NI-700 On-Board Memory Specifications section onRear Panel Components IR RXNI-700 Port Assignment And Functionality NI-700 On-Board Memory SpecificationsNI-700 On-Board Memory Specifications NI-700 Port AssignmentsNI-900 Specifications NI-900 OverviewNI-900 Specifications Front Panel ComponentsSurge damage NI-900 Port Assignment And Functionality NI-900 Port AssignmentsTimeKeeper NI-900 On-Board Memory SpecificationsNI-900 On-Board Memory Specifications Related DocumentsIntroduction NI-700 & NI-900 Hardware Reference Guide Installing into an Equipment Rack DevicePortSystem DPSInstallation Program Run Disable PRD Mode Setting the Configuration DIP Switch for the Program PortBaud Rate Settings Baud Rate Settings on the Configuration DIP SwitchProgram Port, Pinouts, and Signals Program Port Connections and WiringWorking With the Configuration DIP Switch Program Port Connector Pin SignalAXlink Port and LED Modes and Front Panel LED Blink PatternsPort Assignments and Functionality Modes and LED Blink PatternsPreparing Captive Wires Wiring GuidelinesWiring Length Guidelines Wiring Guidelines NI-700 @ 280 mAWiring a Power Connection Using the 4-pin Mini-Phoenix Connector For Data and PowerDB9 Device Port Connections and Wiring RS-232 RS-422 RS-485Pin IRX-RX Port Connection and WiringRS-232/422/485 Device Port Wiring Specifications FunctionInput/Output I/O Port Connections and Wiring Port Wiring SpecificationsPin Signal Function IR/Serial Connector Wiring Specifications per Port IR/Serial Port Connections and WiringEthernet/RJ-45 Port Connections and Wiring Ethernet RJ-45 Pinouts and SignalsRJ-45 wiring diagram Ethernet LEDsEthernet Ports Used By the Integrated Controller Ethernet Port DescriptionsPort type Description Standard Port # Page Page It’s Your World Take Control

NI-700/900 specifications

The AMX NI-700/900 series represents a significant advancement in the realm of audio-visual management solutions, catering primarily to corporate, educational, and large-scale event environments. Designed for versatility and ease of use, the NI-700 and NI-900 serve as pivotal components in modern audio-visual applications, ensuring seamless integration and superior performance.

The NI-700 features a compact design that is perfect for smaller installations, boasting a powerful processor capable of handling multiple video and audio sources simultaneously. It allows for flexible input configurations, with support for HDMI, VGA, and analog audio, making it compatible with a vast array of devices. The user interface is intuitive, designed for both novice and expert users, with customizable presets that streamline the operation of complex systems.

On the other hand, the NI-900 is engineered for larger environments, where its enhanced processing capabilities truly shine. It supports an extended range of inputs and outputs, including multiple HDMI ports and robust audio distribution options. The NI-900 also features advanced signal processing technology, ensuring high-quality audio and video performance, essential for critical presentations and high-stakes events. Both models incorporate built-in support for networked control, allowing users to manage and monitor their systems remotely.

One of the standout features of the AMX NI-700/900 series is their integration with AMX's extensive software ecosystem. This includes the AMX Rapid Project Maker, which simplifies the programming process, enabling quick deployment and configuration of AV systems. The devices also support various third-party control protocols, ensuring compatibility with existing infrastructure and devices.

Durability and reliability are key attributes of the NI-700 and NI-900. Built with high-quality components, these units are designed for continuous operation in demanding environments. Their foam-filled metal chassis protect against physical damage while maintaining a professional aesthetic.

In summary, the AMX NI-700/900 series epitomizes innovation in AV control technology. With their compact designs, extensive input/output options, advanced processing capabilities, and seamless integration with AMX software, these devices stand out as essential tools for achieving high-performance audio-visual management in diverse settings, ensuring that presentations and events are executed flawlessly.
Top Page Image Contents