Agilent Technologies E2050-90003 manual Hardware Requirements

Page 25

Installation

Hardware Requirements

Hardware Requirements

To install the Gateway, you must have the following hardware:

nOne or more of these network-equipped computer systems to act as the LAN client system(s):

qHP 9000 Series 700 workstation

q32-bit personal computer (PC)

nA local area network (LAN) to which the client system(s) and the E2050 LAN/GPIB Gateway can connect via the appropriate LAN cables.

nThe E2050 LAN/GPIB Gateway.

nThe power module and standard power cord to provide power to the Gateway.

nOptionally, a separately purchased rack mount kit in which you can mount the Gateway.

nGPIB instrument(s), including the GPIB cable(s) needed to connect the Gateway to the instrument(s).

Chapter 2

25

Image 25

Contents Page Page Contents 103 Government Restricted Rights Warranty InformationPrinting History Trademark InformationCopyright Information Contacting AgilentRadio and Television Interference Safety ConsiderationsPage Declaration of Conformity Page Introduction Chapter IntroductionGuide Contents How to Use This GuideFor HP-UX Related Software DocumentationE2050 LAN/GPIB Gateway Front Panel E2050 Hardware DescriptionE2050 Hardware Description E2050 LAN/GPIB Gateway Front PanelE2050 LAN/GPIB Gateway Rear Panel E2050 LAN/GPIB Gateway Rear PanelAC/DC Adapter and Standard AC Power Cord AC/DC Adapter and AC Power CordRack Mount Kit Optional Rack Mount Kit Optional ChapterApplication Software Supported E2050 Software/Firmware ArchitectureE2050 Software/Firmware Architecture Typical LAN Connections Chapter Typical LAN ConnectionsLAN Client Server ConfigurationSoftware/Firmware Architecture Chapter Software/Firmware Architecture OverviewEstablishing a Network Connection Using Application SoftwareInstallation Installation Hardware Requirements Hardware RequirementsSoftware Requirements Software RequirementsInstalling the Hardware Installing the HardwareFinding the LAN Hardware Address MAC Configure the Network Record LAN Hardware AddressInstalling the Hardware Connect the Gateway to the Network Installing the Hardware Connecting the Power Module Chapter Installing the Hardware Connect Gpib Cable and Power CordsInstalling the Hardware Observe the Power-On Sequence Installing the Hardware Chapter Configuration Configuration Steps to Set Configuration Values Setting Configuration ValuesConfiguration Values Descriptions Setting Configuration Values0.0 Hpib Allow 156.140.34-48.2 Sec Typically, syslogd obtains its routing information from How Configuration Values are Used When the Config Preset Button is Pressed Configuration Methods Overview Configuration MethodsConfiguration Methods Bootp Route add 192.0.0.192 yoursystemname Enter Using Telnet Configuration Method Windows# Default subnet gateway IP address 120 Ip 156.140.222.201 Enter Configuration Methods Using Telnet Configuration Method HP-UX # Default subnet gateway IP address Telnetcommand value Return Ping 156.140.4.249 Return Packets transmitted, 0 packets received, 100% packet loss Using Bootp Configuration Method HP-UX Be rfc1048 Ping 156.140.4.249 Enter Using Bootp with Tftp Configuration Method HP-UX E2050\ Hostname E2050 Configuration Methods Ping 156.140.4.249 Return Administration Administration Accessing the Telnet Utility Using the Telnet UtilityUsing the Telnet Utility Using the Telnet Utility OFF Exiting the Telnet Utility Telnet CommandsAllow IPaddresses Querying the Gateway Querying the Current ConfigurationQuerying the Firmware Revision Querying the GatewayQuerying Gateway/Client Connections Querying the Configuration MethodServer ID Igpibantctl Igpibgett1delay Setting Default Configuration Values Configuring the GatewayChanging the Configuration Method Configuring the GatewayConfiguring the Gateway Messages Using the Gateway’s syslog FileMaintaining the syslog File Terminating Client Connections Configuring the Gateway Chapter Troubleshooting Troubleshooting Gateway Failure Messages Sicl Error Codes and MessagesGateway Failure Messages IPaddress Syslog File MessagesTroubleshooting Network Configuration Troubleshooting Network ConfigurationVerifying Network Connections Troubleshooting Network Configurations Bootp or Bootp with Tftp Configuration Verifying Gateway Configuration Troubleshooting Gateway ConfigurationSetting Default Configuration Troubleshooting Gateway ConfigurationLAN Conn LED Description Operation Verifying the Configuration MethodTroubleshooting Gateway Configuration Changing the Configuration Method Troubleshooting Bootp Configuration Troubleshooting Telnet ConfigurationTroubleshooting Bootp with Tftp Configuration Client Connection Problems Troubleshooting Client ConnectionsTroubleshooting Client Connections Packets transmitted, 0 packets received, 100% packet loss LAN/GPIB Gateway follow Client Run-time ErrorsTroubleshooting Client Connections Troubleshooting Client Connections Specifications 100 Specifications SpecificationsGpib Characteristics Power RequirementsSpecifications 101 Environmental102 Specifications 103 Glossary104 Glossary GlossaryGlossary 105 106 Glossary Index 107 Index108 Index 109 110