D-Link DKVM-IP1 manual

Page 54

You have to perform the following steps in order to enable Dynamic DNS:

Make sure that the LAN interface of the DKVM-IP1 switch is properly configured.

Enter the Dynamic DNS Settings configuration dialog as shown in Figure 6-20.

Enable Dynamic DNS and change the settings according to your needs (see below).

Enable Dynamic DNS

This enables the Dynamic DNS service. This requires a configured DNS server IP address.

Dynamic DNS server

This is the server name where DKVM-IP1 switch registers itself in regular intervals. Currently, this is a fixed setting since only dyndns.org is supported for now.

Hostname

This is the hostname of the DKVM-IP1 switch that is provided by the Dynamic DNS Server. (use the whole name including the domain, e.g. testserver.dyndns.org , not just the actual hostname).

Username

You have registered this username during your manual registration with the Dynamic DNS Server. Spaces are not allowed in the Nickname.

Password

You have used this password during your manual registration with the Dynamic DNS Server.

Check time

The DKVM-IP1 switch registers itself for initiating the IP address of DKVM-IP1 stored in the Dynamic DNS server at this time.

Check interval

This is the interval for reporting again to the Dynamic DNS server for updating the IP address associated with the Domain Name of the DKVM-IP1 switch.

Warning

The DKVM-IP1 switch has its own independent real time clock. Make sure the time setting of the DKVM-IP1 switch is correct. (see the Section called Date And Time )

51

Image 54
Contents Link DKVM-IP1 Port KVM Switch Over IP Manual Contents Menu Options Installation DKVM-IP1 switch hardware installationVideo modes Initial IP configuration Web interfaceRemote Console Top part of the Remote ConsoleWhen the server is up and running When the server is deadFeatures Package contentsSystem requirement Technical specifications Model NoDKVM-IP1 1port KVM Switch Over IP DescriptionCable diagrams PS/2 Cable VGA CableUSB 2.0 Cable Connecting DKVM-IP1 switch to the host system Operation OverviewStep Connect the monitor to the DKVM-IP1 switch console side Option Ethernet connectionPage Initial Configuration Initial configuration via Dhcp serverDKVM-IP1 switch Setup Tool Authentication Initial configuration via serial consoleDKVM-IP1 switch keyboard settings IP auto configurationKeyboard, Mouse and Video configuration IP addressAuto mouse speed and mouse synchronization Remote Mouse SettingsHost system mouse settings Fast SyncRecommended Mouse Settings Windows XP Mouse SettingsSingle and Double Mouse Mode Special Mouse DriverPrerequisites TelnetLogin into the DKVM-IP1 switch and logout Internet Explorer displaying the encryption key lengthNavigation MainLogout from the DKVM-IP1 switch Remote Console General descriptionMain Window Remote Console Control BarExclusive Access Remote Console Options MenuScaling Mouse HandlingLocal Cursor Video Settings Remote Console Options MenuCursorSoft Keyboard 12. Soft KeyboardLocal Keyboard HotkeysEncoding Remote Console Status Line 15. Encoding17. Status line transfer rate Remote KVM Console Telnet ConsoleQuit HelpCls VersionUpload a Floppy Image Use Image on Windows Share SambaSelecting CD ROM Select Sharing to open the configuration dialog Creating an Image Floppy Images CD ROM/ISO ImagesDd if=/dev/cdrom of=/tmp/cdrom.image Driver Installation Drive redirection17. KVM Vision Viewer Setup step Create a New Device 17. Create a new DeviceDrive Redirection Settings 18. New DeviceOptions Change Password UsersSettings User Console14. User Console Settings Part 15. User Console Settings Part 17. Keyboard and Mouse Settings Keyboard/MousePage Video Network19. Network Settings Part 19. Network Settings Part Dynamic DNS 20. Dynamic DNSPage Security 22. Device Security23. Certificate Settings Certificate24. SSL Certificate Upload Serial Port 25. Serial PortPage Date And Time Event LogPage Page Device Status Board SummaryReset Functions Update FirmwareEven log Page Unit Reset 35 Unit ResetTroubleshooting Certificates CE CertificatePin Assignments Key Codes F12 Printscreen Scroll Lock Break Insert Home Delete Video Modes Rack mount kit installation diagram