Allied Telesis x600-48Ts, x600-24Ts/XP, x600-24Ts-POE, X600-24TS-POE+, X600-48TS/XP SD Card Slot

Page 30

Chapter 1: Overview

SD Card Slot

All of the x600 Series Switches have an SD card slot for storing configuration files and AlliedWare Plus Operating System Software image files on an SD card. See Figure 9.

SD READY

BUSY FAULT

1616

Figure 9. SD Card Slot

SD cards can make it easier for you to upgrade the files on a switch or transfer files between x600 switches. See Figure 10.

LOCK

SD

Memory

Card

1319

Figure 10. SD Card

Note

An SD card is not required for normal operations of the switch.

To insert an SD card, position it so that the manufacturer’s brand label is facing up and press it into the slot until it is flush with the front of the chassis. To remove the SD card, gently press and release the card. The SD card will then pop out so you can grasp it with your fingers.

For information on how to transfer files to and from a SD card, refer to the

AlliedWare Plus Operating System Software Reference Guide.

30

Image 30

Contents Installation Guide Page Electrical Safety and Emissions Standards Translated Safety Statements Contents Overview Preparation Installing the AT-StackXG Module X600-24Ts-POE Switch List of FiguresFigures List of Tables Tables Preface Product Documentation Starting a Management Session Safety Symbols Used in this Document Symbol Meaning DescriptionWhere to Find Web-based Guides Management Software Updates Contacting Allied TelesisOverview ChapterIntroduction Switch Descriptions LEDsX600-24Ts/XP Switch Shows the x600-24Ts/XP switch front and rear panelShows the x600-48Ts switch front and rear panel X600-48Ts/XP Switch X600-44Ts/XPX600-24Ts-POE Switch X600-24Ts-POE+ Switch Connector Type Speed Duplex Mode Maximum Distance 10/100/1000Base-T PortsCable Type Auto-MDI Port PinoutsSFP Transceiver Slots XFP Transceiver Slots Combo Ports Models Ports and SlotsSD Card Slot Port LEDs 10/100/1000 Base-T LEDsLED SFP LEDs x600-24 Port Switch SFP LEDs x600-48 Port Switch SFP Slot LED Descriptions XFP Transceiver Slot LEDsXFP Slot LED System Status LEDs State DescriptionNon PoE Switch Stack LEDs Stack LEDsMstr Secure Digital SD LED Defined in TableTerminal Port Power Over Ethernet PoE and PoE+ PoE PoE+ Enhanced PoE Differences between PoE, PoE+ and Enhanced PoE Overview Implementation 10/100BASE-TX Redundant Power Supplies AT-RPS3204 Redundant Power Supply UnitAT-LBM Loop Back Module VCS Stacking Module AC Power Connector Overview Virtual Chassis Stacking Features of VCStacking Physical Stack VCStackTM IntroductionVCS Stacking Modules, Cables, and Connections VCStack Recovery States Ring ConfigurationEvent on Master Node Reaction on Reaction on Stack Resiliency Link Configurations via Switch Ports Resilient Stacked Topology Stack Formation Role of the Stack MasterCommon Stack Configuration Stack Member Identification Stack Member Failure Recovery Running QoS within a VCS stackVCS Failure Recovery Fallback ActionStack Maintenance Adding a Stack MemberVirtual Chassis Stacking Installing the Hardware Reviewing Safety Precautions X600 Layer 3 Gigabit Ethernet Switch Installation Guide Installing the Hardware Unpacking a Switch Installing the Power Cord Retaining Clip Installing the Switches in an Equipment Rack ActactivityMounting the Switch in a Rack Resetting the Switch 24Ts/XPVC Stacking Module Installation Installing AT-StackXG Module Securing the AT-StackXG Stacking Module Software Reference Installing the Hardware Cabling the Network Ports Twisted Pair and Fiber Optic Specifications Twisted Pair Cable SpecificationsTransceiver Specifications SFP/XFPInstalling SFP/XFP Transceivers Installing an SFP Transceiver1331 1334 Installing an XFP Transceiver Installing an XFP TransceiverCabling the Network Ports Cabling the 10/100/1000Base-T and Fiber Optic Ports Powering on a Switch Connecting the AC Power CordStarting a Local Management Session Cabling the Network Ports Warranty Registration Cabling the Network Ports Troubleshooting Power LED is Off Twisted Pair Port Link LED is Off SFP or XFP LED is Off Transceiver is Installed but the Status is Not Present System Fault LED is Blinking System Fault LED is Steadily On Cannot Establish a Local Out-of-Band Management Session Switch Functions Intermittently Issues with Virtual Stacking Chassis Configuration Technical Specifications Physical SpecificationsAppendix a Environmental Specifications Power SpecificationsCertifications Pin Signal RJ-45 Twisted Pair Port PinoutsPinout Pair AT-RPS3104 17-pin Connector Pinouts RJ-45 Style Serial Terminal Port PinoutsPin Definition AT-RPS3204 21-pin D-combo Port and Connector Pinouts Pin Appendix a Technical Specifications 112

Related manuals

Manual 72 pages 26.86 Kb

Manual 110 pages 37.26 Kb