Allied Telesis at-8116 Set-speed-sel, Set-port-state, Set-aggr-mode, SYSconsoleset-aggr-mode

Page 63

AT-8116 User’s Guide

set-speed-sel

set-port-sel <port-number> {asense10010}

This command speciﬁes if port-number will negotiate a 10Mbps or 100Mbps connection, or it will autosense. If the switch is having difficulty auto-sensing the wire speed, use this command to set the correct value.

Note

If the port’s link partner is in Full Duplex mode and not in ASENSE (or auto-negotiation) mode, ASENSE cannot be selected as the line speed of the port.

set-port-state

This command can be used to enable or disable a port when the Spanning Tree algorithm is not running. When Spanning Tree is running, set-prt-enb should be used instead.

set-port-state < port-number> {enabledisable}

set-aggr-mode

This command sets the device mode: aggressive or relax backoff algorithm.

SYS_console>set-aggr-mode

[arg #0] enter either {enable disable}

SYS_console>

The AT-8116 implements the truncated exponential backoff algorithm deﬁned by the 802.3 standard. The set-aggr-mode command controls the number of consecutive retransmit trials (necessitated by collisions) before restarting the backoff algorithm. In aggressive mode the AT-8116 restarts the backoff algorithm after 4 consecutive transmit trials instead of 16. This results in the switch being more aggressive in accessing the media following a collision.

12-3

Image 63

Contents E R ’ S G U I D E Page Table of Contents Appendix B Rmon Administrative InterfaceAdministrative Interface Accessing the Snmp Agent Network Management SystemsSystem Requirements Software Requirements VT100 Terminal SettingsAccessing the Command Line Interface Remotely Testing the InstallationPage Features of the Command Line Interface Command Line InterfaceGet-comm read Get-comm write Entering CommandsSYSconsole pin Command pin not found Get-comm read writeSYSconsole ping 129.1.1.7 ? ping IP traffic generator System Commands System CommandsSYSconsolesystem Command Line Interface Structure SYSconsoleget-c? Command get-c not found2Commands Matching get-c SYSconsole? Commands GroupsConsole Function Keys Console CommandsHelp-kbd SYSconsolehelp-kbdLogout LoginBanner ClearSet-passwd Set-attr-promptSet-attr-msg Set-attr-textConsole Commands Sys-stat System CommandsSYSconsole System CommandsSet-stst-level level Warm-resetCold-reset Get-stst-levelGet-tftp-srvr Init-nvramGet-sw-file Set-sw-fileSw-dnld Set-fg-paramStart-fg Stop-fg Set-ipIPaddress IP CommandsGet-ip Set-ipSet-ip-cfg IPaddress netmask broadcast If no IP Config. is definedGet-ip-cfg Set-ip-cfgClear-ip-cfg Set-gatew IPaddress SYSconsoleget-gatew Default gateway address isGet-gatew Set-gatewSYSconsoleget-arp-tbl IfIndex IpAddress Address Resolution CommandsGet-arp-tbl Del-arp-entry194.090.136.126 Add-arp-entrySYSconsoleping 194.90.136.23 Ping CommandsPing Ping-stopSYSconsoleping 194.90.136.20 Echo RequestsEcho Responses Ping process press CR for prompt SYSconsole Ping-stop Stop the active ping Process Echo responses Ping process pressPage Get-comm readwrite Snmp CommandsSnmp Community String Commands Get-commSet-auth Snmp Trap Message CommandsSet-comm Get-authAdd-trap Get-trapsSYSconsoleget-rmon-state Del-trapGet-rmon-state SYSconsoledel-trapLock Switching Database CommandsGet-lt-entry Learning TableSYStelnetget-lt-16 Get-lt-16SYStelnetﬁnd-lt-addr 0060e8112265 Find-lt-addrDel-lt-entry index Del-lt-entrySYSconsolefind-lt-addr MAC Address 01-02-03-04-05-06 not in LTSYSconsoledel-lt-entry Del-lt-addrAdd-lt-entry Get-lt-ageSet-lt-age Set-lt-age runnvramall agingtimeSYSconsoleset-lt-age all Page Type vlan to view the related commands SYSconsolevlan Virtual LAN CommandsGet-con-matrix Virtual Broadcast Domains VBC========================== SYSconsoleget-con-matrixDel-vbc-domain runnvram domainid Del-vbc-domainSet-vbc-domain Set-vbc-domain runnvramall portlist Set-vbc-domain allSYSconsoleget-vbc-matrix Get-vbc-matrixSecurity VLANs Set-sec-vlanSvlan Groups Del-sec-vlan runnvram lanid Del-sec-vlanLANs 0 0 0 0 0 0 0 1 1 1 1 1 1 3 4 5 6 7 8 9 0 1+ + + + + + + + SYSconsole Get-svlan-tblGet-svlan-tbl runnvram SYSconsoleget-svlan-tbl runGet-svlan-matrix runnvram SYSconsoleget-svlan-matrix run Get-svlan-matrixPage Get-nv-mon Port Monitoring CommandsSet-mon-port Stop-monClear-nv-mon Save-monPort Conﬁguration Commands Get-port-cfgSYSconsoleget-port-cfg Set-port-dplex Set-port-dplex portnumber halffullSYSconsoleset-port-dplex 2 full SYSconsoleset-aggr-mode Set-speed-selSet-port-state Set-aggr-modePage Switching Statistics Commands Clr-cntGet-eth-cnt Switching Statistics Commands SYSconsoleget-colls-cnt Get-colls-cntGet-rmon-cnt Get-sdist-cntGet-mgm-brcnt =============================================15637 1123754 Set-stp Spanning Tree CommandsSet-stp enabledisable Get-stpSet-br-prio Get-st-bcfgGet-st-pcfg Get-st-syscfgSet-prt-prio Set-prt-enbSet-prt-pcost Page Configuring the AT-8116 Snmp Agent Using an Snmp ManagerSYSconsoleset-gatew New read community Read publicPage Software Troubleshooting Page Tftp Client Download Procedure Software DownloadingRequirements Tftp Server Download Procedure System Default Values System DefaultsPage Table C-1 Console Commands Command Line ReferenceTable C-2 System Commands Table C-4SNMP Commands Table C-3IP CommandsTable C-6 Virtual LAN Commands Table C-5 Switching Database CommandsTable C-7Port Conﬁguration Commands Table C-8Switching Statistics CommandsTable C-9Spanning Tree Commands