Allied Telesis at-8116 manual VT100 Terminal Settings, Software Requirements

Page 8

Administrative Interface

Software Requirements

If you are using a workstation, use the VT100 terminal emulation software appropriate for your workstation.

If you are using a PC to emulate a VT100 terminal, you can use the following software:

❑In a DOS environment:

—MS-DOS 3.30 or later

—PROCOMM PLUS for DOS

❑In a Windows 3.1 environment:

—Microsoft Windows 3.1 or later

—Windows Terminal or PROCOMM PLUS for Windows

❑In Windows 95 or NT

—Hyperterminal

Note

Because of their compatibility and reliability, the software combination listed above are recommended. Other applications may also provide satisfactory results.

VT100 Terminal Settings

Use the following settings when connecting the VT100 terminal or terminal emulator to the AT-8116.

❑Communications Setup

—9600 (baud)

—No Parity

—8 Data Bits, 1 Stop Bit

—No Local Echo

—VT100 Mode

❑Terminate the setup session by pressing Ctrl-C.

For details concerning using the SNMP agent, see Chapter 15, Using an SNMP Manager.

1-4

Image 8

Contents E R ’ S G U I D E Page Table of Contents Appendix B Administrative Interface RmonAdministrative Interface System Requirements Accessing the Snmp AgentNetwork Management Systems VT100 Terminal Settings Software RequirementsTesting the Installation Accessing the Command Line Interface RemotelyPage Command Line Interface Features of the Command Line InterfaceEntering Commands SYSconsole pin Command pin not foundGet-comm read write Get-comm read Get-comm writeSYSconsole ping 129.1.1.7 ? ping IP traffic generator SYSconsolesystem System CommandsSystem Commands 2Commands Matching get-c Command Line Interface StructureSYSconsoleget-c? Command get-c not found Commands Groups SYSconsole?Console Commands Help-kbdSYSconsolehelp-kbd Console Function KeysLogin BannerClear LogoutSet-attr-prompt Set-attr-msgSet-attr-text Set-passwdConsole Commands System Commands Sys-statSystem Commands SYSconsoleWarm-reset Cold-resetGet-stst-level Set-stst-level levelInit-nvram Get-sw-fileSet-sw-file Get-tftp-srvrStart-fg Sw-dnldSet-fg-param Stop-fg IP Commands Get-ipSet-ip Set-ipIPaddressIf no IP Config. is defined Get-ip-cfgSet-ip-cfg Set-ip-cfg IPaddress netmask broadcastClear-ip-cfg SYSconsoleget-gatew Default gateway address is Get-gatewSet-gatew Set-gatew IPaddressAddress Resolution Commands Get-arp-tblDel-arp-entry SYSconsoleget-arp-tbl IfIndex IpAddressAdd-arp-entry 194.090.136.126Ping Commands PingPing-stop SYSconsoleping 194.90.136.23Echo Responses Ping process press CR for prompt SYSconsole SYSconsoleping 194.90.136.20Echo Requests Echo responses Ping process press Ping-stop Stop the active ping ProcessPage Snmp Commands Snmp Community String CommandsGet-comm Get-comm readwriteSnmp Trap Message Commands Set-commGet-auth Set-authGet-traps Add-trapDel-trap Get-rmon-stateSYSconsoledel-trap SYSconsoleget-rmon-stateSwitching Database Commands LockLearning Table Get-lt-entryGet-lt-16 SYStelnetget-lt-16Find-lt-addr SYStelnetﬁnd-lt-addr 0060e8112265Del-lt-entry SYSconsolefind-lt-addrMAC Address 01-02-03-04-05-06 not in LT Del-lt-entry indexDel-lt-addr Add-lt-entryGet-lt-age SYSconsoledel-lt-entrySYSconsoleset-lt-age all Set-lt-ageSet-lt-age runnvramall agingtime Page Virtual LAN Commands Type vlan to view the related commands SYSconsolevlanVirtual Broadcast Domains VBC Get-con-matrixSYSconsoleget-con-matrix ==========================Del-vbc-domain Set-vbc-domain Set-vbc-domain runnvramall portlistSet-vbc-domain all Del-vbc-domain runnvram domainidGet-vbc-matrix SYSconsoleget-vbc-matrixSvlan Groups Security VLANsSet-sec-vlan Del-sec-vlan LANs 0 0 0 0 0 0 0 1 1 1 1 1 13 4 5 6 7 8 9 0 1 Del-sec-vlan runnvram lanidGet-svlan-tbl Get-svlan-tbl runnvramSYSconsoleget-svlan-tbl run + + + + + + + + SYSconsoleGet-svlan-matrix Get-svlan-matrix runnvram SYSconsoleget-svlan-matrix runPage Port Monitoring Commands Set-mon-portStop-mon Get-nv-monSave-mon Clear-nv-monSYSconsoleget-port-cfg Port Conﬁguration CommandsGet-port-cfg SYSconsoleset-port-dplex 2 full Set-port-dplexSet-port-dplex portnumber halffull Set-speed-sel Set-port-stateSet-aggr-mode SYSconsoleset-aggr-modePage Get-eth-cnt Switching Statistics CommandsClr-cnt Switching Statistics Commands Get-colls-cnt Get-rmon-cntGet-sdist-cnt SYSconsoleget-colls-cnt15637 1123754 Get-mgm-brcnt============================================= Spanning Tree Commands Set-stp enabledisableGet-stp Set-stpGet-st-bcfg Get-st-pcfgGet-st-syscfg Set-br-prioSet-prt-pcost Set-prt-prioSet-prt-enb Page Using an Snmp Manager Configuring the AT-8116 Snmp AgentSYSconsoleset-gatew Read public New read communityPage Software Troubleshooting Page Requirements Tftp Client Download ProcedureSoftware Downloading Tftp Server Download Procedure System Defaults System Default ValuesPage Command Line Reference Table C-1 Console CommandsTable C-2 System Commands Table C-3IP Commands Table C-4SNMP CommandsTable C-5 Switching Database Commands Table C-6 Virtual LAN CommandsTable C-9Spanning Tree Commands Table C-7Port Conﬁguration CommandsTable C-8Switching Statistics Commands