Allied Telesis at-8116 Get-stst-level, Set-stst-level level, Warm-reset, Cold-reset, Get-last-err

Page 23

AT-8116 User’s Guide

get-stst-level

This command shows the self-test level (Disable or Enable) of the device.

Default Value: Enable

set-stst-level <level>

This command sets the self-test level of the device. There are two levels of self-test: Disable and Enable. The self-test level is stored in Non-volatile Random Access Memory (NVRAM).

warm-reset

The warm-reset command resets the SNMP Agent software. The Switch conﬁguration is changed according to the values stored in the NVRAM. This command will permit the user to refresh the Switch conﬁguration after a change of the NVRAM parameters. The statistics counters are also reset by the warm-reset command.

cold-reset

This command causes the switch to cold-reset. Cold reset is equivalent to power on the switch.

get-last-err

This command retrieves the most recent system failure for diagnostic purposes.

SYS_console>get-last-err

System information since the last hardware reset

--------------------------------------------

Software resets number: 0

The system never encountered a fatal error

SYS_console>

Note

Software resets number implies executed “warm resets” commands after last “cold reset”.

4-3

Image 23

Contents E R ’ S G U I D E Page Table of Contents Appendix B Rmon Administrative InterfaceAdministrative Interface System Requirements Accessing the Snmp AgentNetwork Management Systems Software Requirements VT100 Terminal SettingsAccessing the Command Line Interface Remotely Testing the InstallationPage Features of the Command Line Interface Command Line InterfaceGet-comm read Get-comm write Entering CommandsSYSconsole pin Command pin not found Get-comm read writeSYSconsole ping 129.1.1.7 ? ping IP traffic generator SYSconsolesystem System CommandsSystem Commands 2Commands Matching get-c Command Line Interface StructureSYSconsoleget-c? Command get-c not found SYSconsole? Commands GroupsConsole Function Keys Console CommandsHelp-kbd SYSconsolehelp-kbdLogout LoginBanner ClearSet-passwd Set-attr-promptSet-attr-msg Set-attr-textConsole Commands Sys-stat System CommandsSYSconsole System CommandsSet-stst-level level Warm-resetCold-reset Get-stst-levelGet-tftp-srvr Init-nvramGet-sw-file Set-sw-fileStart-fg Sw-dnldSet-fg-param Stop-fg Set-ipIPaddress IP CommandsGet-ip Set-ipSet-ip-cfg IPaddress netmask broadcast If no IP Config. is definedGet-ip-cfg Set-ip-cfgClear-ip-cfg Set-gatew IPaddress SYSconsoleget-gatew Default gateway address isGet-gatew Set-gatewSYSconsoleget-arp-tbl IfIndex IpAddress Address Resolution CommandsGet-arp-tbl Del-arp-entry194.090.136.126 Add-arp-entrySYSconsoleping 194.90.136.23 Ping CommandsPing Ping-stopEcho Responses Ping process press CR for prompt SYSconsole SYSconsoleping 194.90.136.20Echo Requests Ping-stop Stop the active ping Process Echo responses Ping process pressPage Get-comm readwrite Snmp CommandsSnmp Community String Commands Get-commSet-auth Snmp Trap Message CommandsSet-comm Get-authAdd-trap Get-trapsSYSconsoleget-rmon-state Del-trapGet-rmon-state SYSconsoledel-trapLock Switching Database CommandsGet-lt-entry Learning TableSYStelnetget-lt-16 Get-lt-16SYStelnetﬁnd-lt-addr 0060e8112265 Find-lt-addrDel-lt-entry index Del-lt-entrySYSconsolefind-lt-addr MAC Address 01-02-03-04-05-06 not in LTSYSconsoledel-lt-entry Del-lt-addrAdd-lt-entry Get-lt-ageSYSconsoleset-lt-age all Set-lt-ageSet-lt-age runnvramall agingtime Page Type vlan to view the related commands SYSconsolevlan Virtual LAN CommandsGet-con-matrix Virtual Broadcast Domains VBC========================== SYSconsoleget-con-matrixDel-vbc-domain runnvram domainid Del-vbc-domainSet-vbc-domain Set-vbc-domain runnvramall portlist Set-vbc-domain allSYSconsoleget-vbc-matrix Get-vbc-matrixSvlan Groups Security VLANsSet-sec-vlan Del-sec-vlan runnvram lanid Del-sec-vlanLANs 0 0 0 0 0 0 0 1 1 1 1 1 1 3 4 5 6 7 8 9 0 1+ + + + + + + + SYSconsole Get-svlan-tblGet-svlan-tbl runnvram SYSconsoleget-svlan-tbl runGet-svlan-matrix runnvram SYSconsoleget-svlan-matrix run Get-svlan-matrixPage Get-nv-mon Port Monitoring CommandsSet-mon-port Stop-monClear-nv-mon Save-monSYSconsoleget-port-cfg Port Conﬁguration CommandsGet-port-cfg SYSconsoleset-port-dplex 2 full Set-port-dplexSet-port-dplex portnumber halffull SYSconsoleset-aggr-mode Set-speed-selSet-port-state Set-aggr-modePage Get-eth-cnt Switching Statistics CommandsClr-cnt Switching Statistics Commands SYSconsoleget-colls-cnt Get-colls-cntGet-rmon-cnt Get-sdist-cnt15637 1123754 Get-mgm-brcnt============================================= Set-stp Spanning Tree CommandsSet-stp enabledisable Get-stpSet-br-prio Get-st-bcfgGet-st-pcfg Get-st-syscfgSet-prt-pcost Set-prt-prioSet-prt-enb Page Configuring the AT-8116 Snmp Agent Using an Snmp ManagerSYSconsoleset-gatew New read community Read publicPage Software Troubleshooting Page Requirements Tftp Client Download ProcedureSoftware Downloading Tftp Server Download Procedure System Default Values System DefaultsPage Table C-1 Console Commands Command Line ReferenceTable C-2 System Commands Table C-4SNMP Commands Table C-3IP CommandsTable C-6 Virtual LAN Commands Table C-5 Switching Database CommandsTable C-9Spanning Tree Commands Table C-7Port Conﬁguration CommandsTable C-8Switching Statistics Commands