Allied Telesis at-8116 manual Using an Snmp Manager, Configuring the AT-8116 Snmp Agent

Page 73

Chapter 15

Using an SNMP Manager

This chapter contains instructions for the conﬁguration and management of the AT-8116 SNMP Management System.

Configuring the AT-8116 SNMP Agent

Global Setup

Once connected to the network and powered ON, the AT-8116 starts operating according to factory-set default values. However, to ensure proper operation and maximum performance speciﬁc to your network conﬁguration and to provide SNMP access, some environment-speciﬁc parameters must be conﬁgured through the Command Line Interface.

If you are conﬁguring the switch for the ﬁrst time:

1.Connect a terminal to the RS-232 connector.

2.Log in to the Command Line Interface.

3.Initialize all the AT-8116 parameters to their default values (see Table 1, System Default Values). Use the following command sequence:

init-nvram (deletes all current NVRAM configrations) warm-reset (loads the NVRAM configuration)

4.Wait until you see the LOGIN prompt again. Login to the CLI. Now all system parameters have been initialized to their default values.

15-1

Image 73

Contents E R ’ S G U I D E Page Table of Contents Appendix B Rmon Administrative InterfaceAdministrative Interface Network Management Systems Accessing the Snmp AgentSystem Requirements Software Requirements VT100 Terminal SettingsAccessing the Command Line Interface Remotely Testing the InstallationPage Features of the Command Line Interface Command Line InterfaceSYSconsole pin Command pin not found Entering CommandsGet-comm read write Get-comm read Get-comm writeSYSconsole ping 129.1.1.7 ? ping IP traffic generator System Commands System CommandsSYSconsolesystem SYSconsoleget-c? Command get-c not found Command Line Interface Structure2Commands Matching get-c SYSconsole? Commands GroupsHelp-kbd Console CommandsSYSconsolehelp-kbd Console Function KeysBanner LoginClear LogoutSet-attr-msg Set-attr-promptSet-attr-text Set-passwdConsole Commands Sys-stat System CommandsSYSconsole System CommandsCold-reset Warm-resetGet-stst-level Set-stst-level levelGet-sw-file Init-nvramSet-sw-file Get-tftp-srvrSet-fg-param Sw-dnldStart-fg Stop-fg Get-ip IP CommandsSet-ip Set-ipIPaddressGet-ip-cfg If no IP Config. is definedSet-ip-cfg Set-ip-cfg IPaddress netmask broadcastClear-ip-cfg Get-gatew SYSconsoleget-gatew Default gateway address isSet-gatew Set-gatew IPaddressGet-arp-tbl Address Resolution CommandsDel-arp-entry SYSconsoleget-arp-tbl IfIndex IpAddress194.090.136.126 Add-arp-entryPing Ping CommandsPing-stop SYSconsoleping 194.90.136.23Echo Requests SYSconsoleping 194.90.136.20Echo Responses Ping process press CR for prompt SYSconsole Ping-stop Stop the active ping Process Echo responses Ping process pressPage Snmp Community String Commands Snmp CommandsGet-comm Get-comm readwriteSet-comm Snmp Trap Message CommandsGet-auth Set-authAdd-trap Get-trapsGet-rmon-state Del-trapSYSconsoledel-trap SYSconsoleget-rmon-stateLock Switching Database CommandsGet-lt-entry Learning TableSYStelnetget-lt-16 Get-lt-16SYStelnetﬁnd-lt-addr 0060e8112265 Find-lt-addrSYSconsolefind-lt-addr Del-lt-entryMAC Address 01-02-03-04-05-06 not in LT Del-lt-entry indexAdd-lt-entry Del-lt-addrGet-lt-age SYSconsoledel-lt-entrySet-lt-age runnvramall agingtime Set-lt-ageSYSconsoleset-lt-age all Page Type vlan to view the related commands SYSconsolevlan Virtual LAN CommandsGet-con-matrix Virtual Broadcast Domains VBC========================== SYSconsoleget-con-matrixSet-vbc-domain Set-vbc-domain runnvramall portlist Del-vbc-domainSet-vbc-domain all Del-vbc-domain runnvram domainidSYSconsoleget-vbc-matrix Get-vbc-matrixSet-sec-vlan Security VLANsSvlan Groups LANs 0 0 0 0 0 0 0 1 1 1 1 1 1 Del-sec-vlan3 4 5 6 7 8 9 0 1 Del-sec-vlan runnvram lanidGet-svlan-tbl runnvram Get-svlan-tblSYSconsoleget-svlan-tbl run + + + + + + + + SYSconsoleGet-svlan-matrix runnvram SYSconsoleget-svlan-matrix run Get-svlan-matrixPage Set-mon-port Port Monitoring CommandsStop-mon Get-nv-monClear-nv-mon Save-monGet-port-cfg Port Conﬁguration CommandsSYSconsoleget-port-cfg Set-port-dplex portnumber halffull Set-port-dplexSYSconsoleset-port-dplex 2 full Set-port-state Set-speed-selSet-aggr-mode SYSconsoleset-aggr-modePage Clr-cnt Switching Statistics CommandsGet-eth-cnt Switching Statistics Commands Get-rmon-cnt Get-colls-cntGet-sdist-cnt SYSconsoleget-colls-cnt============================================= Get-mgm-brcnt15637 1123754 Set-stp enabledisable Spanning Tree CommandsGet-stp Set-stpGet-st-pcfg Get-st-bcfgGet-st-syscfg Set-br-prioSet-prt-enb Set-prt-prioSet-prt-pcost Page Configuring the AT-8116 Snmp Agent Using an Snmp ManagerSYSconsoleset-gatew New read community Read publicPage Software Troubleshooting Page Software Downloading Tftp Client Download ProcedureRequirements Tftp Server Download Procedure System Default Values System DefaultsPage Table C-1 Console Commands Command Line ReferenceTable C-2 System Commands Table C-4SNMP Commands Table C-3IP CommandsTable C-6 Virtual LAN Commands Table C-5 Switching Database CommandsTable C-8Switching Statistics Commands Table C-7Port Conﬁguration CommandsTable C-9Spanning Tree Commands