Linksys Complete Manual for SRW2016 - Downloading and Startup Procedures

Page 71

Appendix C

Appendix C:

Downloading using

Xmodem

Startup Menu Procedures

The Startup menu can be entered when booting the device. There is a two second window of time to enter the Startup Menu immediately after the POST test. The menu can be accessed directly from a terminal connected to the console port. The Startup menu procedures can be done using the ASCII terminal or Windows HyperTerminal.

The software download procedure is performed when a new version must be downloaded to replace corrupted files, update or upgrade the system software. To download software from the Startup menu:

To enter the Startup menu:

1.Power off your computer and Switch.

2.Connect the provided null modem cable from the COM port on your computer to the Console port on the Switch.

3.Power on your computer and launch HyperTerminal, follow the instructions in Chapter 4: Configuration Using the Console Interface to configure HyperTerminal to connect to the Switch.

4.Power on the Switch and watch for the auto-boot message:

Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.

Auto-Boot Message

Downloading using Xmodem

5.When the auto-boot message appears, press the Enter key to access the Startup menu.

Startup Menu

NOTE: If a selection is not made within 35 seconds (default), the device times out and you will need to disconnect the power to restart the process.

6.Select [1] Download Software and a message will appear Downloading code using XMODEM with characters running across the screen.

If you do not perform the remaining steps to locate the file for download within a certain time, the device will reset.

7.Select Send File from the Transfer pull-down menu.

Send File

8.In the Filename: field, enter the file path for the file to be downloaded or click Browse to locate the file.

Only valid files, with a *.ros or *.rfb suffix, that have been provided by Linksys, can be downloaded. Downloading invalid files will result in unpredictable behavior.

Ensure that the Xmodem protocol is selected in the Protocol: field.

WebView Switches

64

Image 71

Contents WebView Switches Online Resources About This GuideAbout This Guide Icon DescriptionsTable of Contents Advanced Configuration Security Radius Security TACACS+ Security 802.1x Settings Appendix B Windows Help Appendix D GlossaryAppendix H Software License Agreement Introduction ChapterChapter Introduction SRW2048 Chapter Product OverviewProduct Overview Product Overview SRW2024SRW2016 SRW248G4 SRW224G4 Refer to Configuration Using Overview Connecting the SwitchBefore You Install the Switch Placement OptionsConfiguring the Switch Hardware InstallationConnecting to the Switch through a Telnet Session Chapter Configuration Using Console InterfaceSystem Configuration Menu Switch Main MenuManagement Settings Telnet Configuration Username & Password Settings IP Configuration Http Network Configuration File Management Port StatusHelp Port ConfigurationSetup Summary Chapter Advanced ConfigurationAdvanced Configuration Accessing the Web-based UtilityIdentification Setup Network SettingsIP Configuration System InformationDaylight Saving Setup TimeSet Time Local TimePort Management Port Settings Setup Green EthernetPort Settings Port Configuration Link Aggregation Detail Port Management Link AggregationVlan Range Port Management LacpVlan Management Create Vlan Single VlanVlan Management Ports to Vlan Vlan Management Port SettingVlan Management Gvrp Vlan Management Vlan to PortsStatistics Rmon Statistics Rmon History Statistics Rmon HistoryLog Table Alarm Entry Indicates a specific alarm Statistics Rmon AlarmRmon Events Log Statistics Rmon EventsStatistics Port Utilization Add EventStatistics Gvrp Statistics Statistics 802.1x StatisticsACL IP Based ACL ACL MAC Based ACL Security Radius Security ACL BindingSecurity TACACS+ Security 802.1x SettingsSecurity Port Security 802.1x Settings Setting TimerSecurity Multiple Hosts QoS QoS CoS SettingsSecurity Storm Control QoS Bandwidth QoS Queue SettingsQoS Dscp Settings CoS DefaultAdvanced Mode Out of Profile Dscp QoS Basic ModeQoS Advanced Mode Spanning Tree Advanced Mode Policy NameAdvanced Mode New Class Map Spanning Tree Global STP Global SettingSpanning Tree STP Status Bridge Settings Spanning Tree STP Port SettingsSpanning Tree Rstp Port Settings Spanning Tree Mstp Properties Spanning Tree Mstp Instance Settings Multicast Igmp Snooping Multicast Bridge Multicast Forward All Multicast Bridge MulticastSnmp Views Snmp Global ParametersSnmp Group Membership Snmp Group ProfileSnmp Communities Advanced Table Snmp Notification FilterBase Table Snmp Notification Recipient Admin User AuthenticationQuery Admin Jumbo FramesAdmin Static Address Admin Logging Admin Dynamic AddressAdmin Cable Test Admin Port MirroringVia Tftp Admin Save ConfigurationAdmin Firmware Upgrade BackupAdmin Server Logs Admin RebootAdmin Factory Defaults Admin Flash Logs Admin Memory LogsFiber Optic Cabling Appendix aAppendix a About Gigabit Ethernet Fiber Optic Cabling Gigabit EthernetNetwork Neighborhood/My Network Places Appendix BAppendix B Windows Help Shared ResourcesAppendix C Appendix C Downloading using XmodemStartup Menu Procedures Downloading using Xmodem Glossary Appendix DAppendix D Glossary Glossary Smtp Simple Mail Transfer Protocol The standard e Appendix D Appendix E Appendix E SpecificationsSpecifications Specifications Environmental Security MAC Address port security† Appendix F Warranty InformationLimited Warranty Obtaining Warranty ServiceTechnical Support Warranty InformationRegulatory Information Appendix GRegulatory Information Appendix G Norsk Norwegian Miljøinformasjon for kunder i EU Appendix G Software Licenses Appendix HAppendix H Software License Agreement Software in Linksys ProductsSoftware License Agreement SchedulePreamble Appendix H END of Terms and Conditions END of Schedule Appendix H END of Schedule 3s Contact Information Appendix

Related manuals

Manual 123 pages 42.48 Kb

Manual 3 pages 47.48 Kb

Manual 2 pages 1.75 Kb