Linksys SLM224G4S (G5), SLM248G4S (G5) manual Port Management Lacp, Global Parameter, Port Priority

Page 27

Chapter 5

Configuration Using the Web-based Utility

Port Management > Link Aggregation > Detail

LAG  The LAG number (1-8). To display or edit another LAG, select the number from the drop-down menu.

Description  The user-defined LAG description of up to 64 characters. This field is blank by default.

LACP  Select the checkbox to enable Link Aggregation Control Protocol (LACP).

LAG Type  (Read-only) The LAG type. The values are:

•eth100m  The LAG contains 100 Mbps Ethernet ports.

•eth1000m  The LAG contains 1000 Mbps Ethernet ports.

Administrative Status  The LAG’s administrative status. Select either Up or Down to enable or disable the LAG.

Current Status  (Read-only) The LAG’s status, either Up or Down.

Admin Auto Negotiation  Select Enable (default) or Disable to enable or disable Auto-Negotiation on the LAG. Auto-Negotiation allows a LAG to advertise its transmission rate, duplex mode, and flow control settings to other LAGs.

Current Auto Negotiation  (Read-only) The LAG’s current Auto-Negotiation status.

Admin Speed  Use this to manually set the LAG’s configured transmission rate in Mbps. You can select 10M, 100M, or 1000M (Gigabit ports only). Before you change this setting, make sure that Admin Auto Negotiation is disabled.

Current LAG Speed  (Read-only) The LAG’s current rate in Mbps.

Admin Flow Control  Select Enable or Disable to manually enable or disable flow control, or select Auto- Negotiation for automatic selection of flow control.

Current Flow Control  (Read-only) The current flow control setting.

Select Ports  To add a port to the LAG, select its checkbox in this section. You can select up to 8 ports per LAG.

Click Save to save the settings and leave the screen open. Click Save & Close to save the settings and close the screen. Click Close to close the screen without saving the settings.

Port Management > LACP

In addition to LAGs that you create by manually grouping ports together, you can also use the Link Aggregation Control Protocol (LACP) to automatically negotiate a LAG link between the Switch and another network device.

The LACP screen contains fields for configuring LACP LAGs.

Port Management > LACP

Global Parameter

LACP System Priority  The global LACP priority value, from 1 to 65535. The default value is 1.

Port Priority

Unit No  The number of the unit that you are managing.

Port  The port to which the timeout and priority values will be assigned. To configure a different port, select it from the drop-down menu. If the port is not listed, click Next in the LACP Port Table.

LACP Port Priority  Defines the LACP priority value for the port, from 1 to 65535. The default value is 1.

LACP Timeout  The administrative LACP timeout value. Select either Short or Long (default).

24/48-Port 10/100 + 4-Port Gigabit Resilient Clustering Smart Switch with 2 Combo SFPs

21

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Port or 48-Port 10/100 + Online Resources About This GuideAbout This Guide Icon DescriptionsTable of Contents Snmp Appendix B About Switch Stacking Appendix C GlossaryGigabit Ethernet Fiber Optic Cabling Appendix G Contact Information Appendix D SpecificationsAppendix E Warranty Information Appendix F Regulatory InformationIntroduction ChapterBack Panel Chapter Product OverviewProduct Overview Front PanelSLM248G4S Placement Options Chapter InstallationInstallation Pre-Installation ConsiderationsHardware Installation Desktop PlacementRack-Mount Placement Configuring Stacking Mode Uplinking the SwitchReplacing a Stacked Switch Connect port G1 on Unit 2 to port G2 on UnitConnect port G1 on Unit 3 to port G2 on Unit Login screen appears. Proceed to the Login section below Chapter Configuration Using Console InterfaceUsing the HyperTerminal Application Using telnetSystem Configuration Menu How to Use the Console InterfaceLogin Switch Main MenuManagement Settings User & Password SettingsSystem Information IP Configuration Security SettingsFile Management Network ConfigurationRestore System Default Settings Reboot SystemStack Configuration Help Port ConfigurationSystem Mode Port StatusDevice Information Chapter Configuration Using Web-based UtilitySetup Setup SummaryDNS Server The IP address of your ISP’s server that Setup ZoomSetup Network Settings Default Gateway The IP address default 0.0.0.0Daylight Saving Setup TimeIdentification Local TimeSntp Servers Setup Stack ManagementPort Management Port Settings Port ManagementPort Configuration Port Management Link Aggregation LAG ConfigurationPort Priority Lacp screen contains fields for configuring Lacp LAGsPort Management Lacp Global ParameterLacp Port Table Vlan Management Port SettingsVlan Management Vlan Management Create VlanVlan Management Port to Vlan Vlan Management Vlan to PortJoin Vlan to Port Statistics Rmon Statistics StatisticsRmon History Table Statistics Rmon HistoryRmon History Log TableAdd Alarm Statistics Rmon AlarmsStatistics Port Utilization Statistics Rmon EventsStatistics Interface Statistics Ethernet-like Security 802.1x SettingsSecurity InterfaceSecurity Port Security Setting TimerWeb IP Filtering Security Management Access ListSecurity Storm Control Security RadiusBroadcast Only Counts only Broadcast traffic CoS Settings screen is used to enable or disable CoS QoS CoS SettingsCoS Settings CoS DefaultQoS Queue Settings QoS Dscp SettingsQoS Bandwidth QoS Basic Mode Spanning TreeSpanning Tree STP Status Spanning Tree Global STP Spanning Tree STP Port SettingsGlobal Setting Bridge SettingsIgmp Global Vlan Igmp SettingsMulticast Multicast Igmp SnoopingMulticast Bridge Multicast Forward All Multicast Bridge MulticastSnmp Views Snmp Global ParametersSnmp Group Profile Snmp Group MembershipUser Name Provides a user-defined local user list Snmp Communities Advanced Table Snmp Notification FilterSnmp Notification Recipient Base TableLocal User Edit AdminAdmin User Authentication User AuthenticationClear Table If selected, this clears the MAC Address table Admin Static AddressAdmin Dynamic Address Secure The entry is defined for locked portsAdmin Port Mirroring Admin Cable TestQuery Admin Save Configuration Admin Firmware Upgrade Admin RebootAdmin Factory Default Admin Logging Admin Server LogsAdmin Memory Logs Logout Admin Flash LogsFiber Optic Cabling Appendix aAppendix a About Gigabit Ethernet Fiber Optic Cabling Gigabit EthernetStack Building Quick Start Appendix B About Switch StackingAbout Switch Stacking Appendix BUnit ID Allocation Advanced StackingStack Resiliency Unit IDsStack Units Startup Process Master DiscoveryMaster Election Replacing a Failed Stack Member in a Running Stack Unit and Port ConfigurationUser Controls Stacking ExamplesStack Master Failure and Replacement Splitting a Stack Subgroup Contains Both Master Unit and Backup Master UnitBoth Stacks Kept Running During Insertion Merging Two StacksInserting Too Many Units Stacking Cable FailureAppendix C Appendix C GlossaryGlossary Glossary Mail protocol on the Internet Packet a unit of data sent over a networkAppendix C Appendix D Specifications SpecificationsAppendix D 802.3z Gigabit Ethernet DimensionsUnit Weight SLM224G4S 1,927 kg 802.3 10BASE-T EthernetAppendix E Warranty InformationLimited Warranty Obtaining Warranty ServiceTechnical Support Warranty InformationRegulatory Information Appendix FRegulatory Information Appendix F Norsk Norwegian Miljøinformasjon for kunder i EU Appendix F Contact Information Appendix G8012510A-AI
Top Page Image Contents