Linksys SLM224G4S (G5), SLM248G4S (G5) manual Multicast Bridge Multicast Forward All

Page 43

Chapter 5

Configuration Using the Web-based Utility

Auto Learn  Select this option to enable Auto Learn on the device. If Auto Learn is enabled, the device automatically learns where other Multicast groups are located. The default is enabled (option is selected).

Host Timeout  Indicates the amount of time host waits to receive a message before timing out. The default time is

260seconds.

MRouter Timeout  Indicates the amount of the time the Multicast router waits to receive a message before it times out. The default value is 300 seconds.

Leave Timeout  Indicates the amount of time the host waits, after requesting to leave the IGMP group and not receiving a Join message from another station, before timing out. If a Leave Timeout occurs, the switch notifies the Multicast device to stop sending traffic The Leave Timeout value is either user-defined, or an immediate leave value. The default timeout is 10 seconds.

Click Update to update the screen with your changes.

Click Save Settings to save the changes, or Cancel Changes to cancel the changes.

Multicast > Bridge Multicast

The Bridge Multicast screen displays the ports and LAGs attached to the Multicast service group in the Ports and LAGs tables. The Port and LAG tables also reflect the manner in which the port or LAGs joined the Multicast group.

Multicast > Bridge Multicast

Ports can be added either to existing groups or to new Multicast service groups. The Bridge Multicast screen permits new Multicast service groups to be created. The Bridge Multicast screen also assigns ports to a specific Multicast service address group.

The Bridge Multicast screen contains the following fields:

VLAN ID  Identifies a VLAN to be configured to a Multicast service.

Bridge Multicast Address  Identifies the Multicast group MAC address/IP address.

Bridge IP Multicast  Displays the port that can be added to a Multicast service.

Interface, Gigabit, LAG  Lists switch interfaces and LAGs that can be added to a Multicast service. The configuration options are as follows:

•Static  Indicates the port is user-defined.

•Dynamic  Indicates the port is configured dynamically.

•Forbidden  Forbidden ports are not included the Multicast group, even if IGMP snooping designated the port to join a Multicast group.

•None  The port is not configured for Multicast service.

Click Add to List to add the configured static multicast address to the table at the bottom of the screen.

Click Show All to display all multicast addresses on all VLANs in the table at the bottom of the screen.

Click Save Settings to save the changes, or Cancel Changes to cancel the changes.

Multicast > Bridge Multicast Forward All

The Bridge Multicast Forward All screen contains fields for attaching ports or LAGs to a device that is attached to a neighboring Multicast router or switch.

Multicast > Bridge Multicast Forward All

Once IGMP Snooping is enabled, Multicast packets are forwarded to the appropriate port or VLAN.

24/48-Port 10/100 + 4-Port Gigabit Resilient Clustering Smart Switch with 2 Combo SFPs

37

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Port or 48-Port 10/100 + Online Resources About This GuideAbout This Guide Icon DescriptionsTable of Contents Snmp Appendix C Glossary Appendix B About Switch StackingGigabit Ethernet Fiber Optic Cabling Appendix G Contact Information Appendix D SpecificationsAppendix E Warranty Information Appendix F Regulatory InformationIntroduction ChapterBack Panel Chapter Product OverviewProduct Overview Front PanelSLM248G4S Placement Options Chapter InstallationInstallation Pre-Installation ConsiderationsDesktop Placement Hardware InstallationRack-Mount Placement Configuring Stacking Mode Uplinking the SwitchConnect port G1 on Unit 2 to port G2 on Unit Replacing a Stacked SwitchConnect port G1 on Unit 3 to port G2 on Unit Login screen appears. Proceed to the Login section below Chapter Configuration Using Console InterfaceUsing the HyperTerminal Application Using telnetSystem Configuration Menu How to Use the Console InterfaceLogin Switch Main MenuUser & Password Settings Management SettingsSystem Information IP Configuration Security SettingsFile Management Network ConfigurationReboot System Restore System Default SettingsStack Configuration Help Port ConfigurationSystem Mode Port StatusDevice Information Chapter Configuration Using Web-based UtilitySetup Setup SummaryDNS Server The IP address of your ISP’s server that Setup ZoomSetup Network Settings Default Gateway The IP address default 0.0.0.0Daylight Saving Setup TimeIdentification Local TimeSntp Servers Setup Stack ManagementPort Management Port Settings Port ManagementPort Configuration Port Management Link Aggregation LAG ConfigurationPort Priority Lacp screen contains fields for configuring Lacp LAGsPort Management Lacp Global ParameterLacp Port Table Vlan Management Port SettingsVlan Management Vlan Management Create VlanVlan Management Vlan to Port Vlan Management Port to VlanJoin Vlan to Port Statistics Rmon Statistics StatisticsRmon History Table Statistics Rmon HistoryRmon History Log TableAdd Alarm Statistics Rmon AlarmsStatistics Rmon Events Statistics Port UtilizationStatistics Interface Statistics Ethernet-like Security 802.1x SettingsSecurity InterfaceSecurity Port Security Setting TimerWeb IP Filtering Security Management Access ListSecurity Radius Security Storm ControlBroadcast Only Counts only Broadcast traffic CoS Settings screen is used to enable or disable CoS QoS CoS SettingsCoS Settings CoS DefaultQoS Dscp Settings QoS Queue SettingsQoS Bandwidth Spanning Tree QoS Basic ModeSpanning Tree STP Status Spanning Tree Global STP Spanning Tree STP Port SettingsGlobal Setting Bridge SettingsIgmp Global Vlan Igmp SettingsMulticast Multicast Igmp SnoopingMulticast Bridge Multicast Forward All Multicast Bridge MulticastSnmp Views Snmp Global ParametersSnmp Group Membership Snmp Group ProfileUser Name Provides a user-defined local user list Snmp Communities Advanced Table Snmp Notification FilterSnmp Notification Recipient Base TableLocal User Edit AdminAdmin User Authentication User AuthenticationClear Table If selected, this clears the MAC Address table Admin Static AddressAdmin Dynamic Address Secure The entry is defined for locked portsAdmin Cable Test Admin Port MirroringQuery Admin Save Configuration Admin Reboot Admin Firmware UpgradeAdmin Factory Default Admin Server Logs Admin LoggingAdmin Memory Logs Logout Admin Flash LogsFiber Optic Cabling Appendix aAppendix a About Gigabit Ethernet Fiber Optic Cabling Gigabit EthernetStack Building Quick Start Appendix B About Switch StackingAbout Switch Stacking Appendix BUnit ID Allocation Advanced StackingStack Resiliency Unit IDsMaster Discovery Stack Units Startup ProcessMaster Election Replacing a Failed Stack Member in a Running Stack Unit and Port ConfigurationUser Controls Stacking ExamplesStack Master Failure and Replacement Splitting a Stack Subgroup Contains Both Master Unit and Backup Master UnitBoth Stacks Kept Running During Insertion Merging Two StacksInserting Too Many Units Stacking Cable FailureAppendix C Glossary Appendix CGlossary Glossary Mail protocol on the Internet Packet a unit of data sent over a networkAppendix C Specifications Appendix D SpecificationsAppendix D 802.3z Gigabit Ethernet DimensionsUnit Weight SLM224G4S 1,927 kg 802.3 10BASE-T EthernetAppendix E Warranty InformationLimited Warranty Obtaining Warranty ServiceTechnical Support Warranty InformationRegulatory Information Appendix FRegulatory Information Appendix F Norsk Norwegian Miljøinformasjon for kunder i EU Appendix F Contact Information Appendix G8012510A-AI
Top Page Image Contents