Linksys SLM224G4S (G5), SLM248G4S (G5) manual Statistics Port Utilization, Statistics Rmon Events

Page 33

Chapter 5

Configuration Using the Web-based Utility

	Interval Defines the alarm interval time in seconds.	Event Table
	Owner Displays the device or user that defined the alarm.	The Event Table lists all events defined using the Add Event

	Click Add to List to add an entry to the Alarm Table.	fields. The Event Table contains columns for all the Add
	Alarm Table	Event fields, plus the following additional column:
	Alarm Table	Time Displays the time that the event occurred.
		Time Displays the time that the event occurred.
	The Alarm Table lists the alarms that have been defined	Statistics > Port Utilization
	using the Add Alarm section. The Alarm Table contains a	Statistics > Port Utilization
	colunn for each field in the Add Alarm section, plus the
	following column:
	Counter Value Displays the current counter value for the
	particular alarm.
	Statistics > RMON Events
	The RMON Events screen is used to define RMON events.

				Statistics > Port Utilization
			The Port Utilization screen displays the amount of resources
			each interface is currently consuming. Ports in green are
			functioning normally, while ports in red are currently
			transmitting an excessive amount of network traffic.
			Refresh Rate Select the rate at which to refresh the
			statistics display: No Refresh (default), 15 sec, 30 sec, or

	Statistics > RMON Events		60 sec.
Add Event			Statistics > Interface Statistics
Event Entry Displays the event.
Event Entry Displays the event.
Community Displays the community to which the event
belongs.
Description Displays the user-defined event description.
Type Describes the event type. Possible values are:
• None Indicates that no event occurred.
• Log Indicates that the event is a log entry.•Trap.
	Indicates that the event is a trap.
• Log and Trap Indicates that the event is both a log
	entry and a trap.
Owner Displays the device or user that defined the
event.
Click Add to List to add the configured RMON event to
the Event Table at the bottom of the screen.
the Event Table at the bottom of the screen.				Statistics > Interface Statistics
24/48-Port 10/100 + 4-Port Gigabit Resilient Clustering Smart Switch with 2 Combo SFPs					27

Image 33

Contents Port or 48-Port 10/100 + About This Guide About This GuideIcon Descriptions Online ResourcesTable of Contents Snmp Appendix B About Switch Stacking Appendix C GlossaryGigabit Ethernet Fiber Optic Cabling Appendix E Warranty Information Appendix D SpecificationsAppendix F Regulatory Information Appendix G Contact InformationIntroduction ChapterProduct Overview Chapter Product OverviewFront Panel Back PanelSLM248G4S Installation Chapter InstallationPre-Installation Considerations Placement OptionsHardware Installation Desktop PlacementRack-Mount Placement Configuring Stacking Mode Uplinking the SwitchReplacing a Stacked Switch Connect port G1 on Unit 2 to port G2 on UnitConnect port G1 on Unit 3 to port G2 on Unit Using the HyperTerminal Application Chapter Configuration Using Console InterfaceUsing telnet Login screen appears. Proceed to the Login section belowLogin How to Use the Console InterfaceSwitch Main Menu System Configuration MenuManagement Settings User & Password SettingsSystem Information IP Configuration Security SettingsFile Management Network ConfigurationRestore System Default Settings Reboot SystemStack Configuration System Mode Port ConfigurationPort Status HelpSetup Chapter Configuration Using Web-based UtilitySetup Summary Device InformationSetup Network Settings Setup ZoomDefault Gateway The IP address default 0.0.0.0 DNS Server The IP address of your ISP’s server thatIdentification Setup TimeLocal Time Daylight SavingPort Management Port Settings Setup Stack ManagementPort Management Sntp ServersPort Configuration Port Management Link Aggregation LAG ConfigurationPort Management Lacp Lacp screen contains fields for configuring Lacp LAGsGlobal Parameter Port PriorityVlan Management Vlan Management Port SettingsVlan Management Create Vlan Lacp Port TableVlan Management Port to Vlan Vlan Management Vlan to PortJoin Vlan to Port Statistics Rmon Statistics StatisticsRmon History Statistics Rmon HistoryLog Table Rmon History TableAdd Alarm Statistics Rmon AlarmsStatistics Port Utilization Statistics Rmon EventsStatistics Interface Statistics Security Security 802.1x SettingsInterface Ethernet-likeSecurity Port Security Setting TimerWeb IP Filtering Security Management Access ListSecurity Storm Control Security RadiusBroadcast Only Counts only Broadcast traffic CoS Settings QoS CoS SettingsCoS Default CoS Settings screen is used to enable or disable CoSQoS Queue Settings QoS Dscp SettingsQoS Bandwidth QoS Basic Mode Spanning TreeSpanning Tree STP Status Global Setting Spanning Tree STP Port SettingsBridge Settings Spanning Tree Global STPMulticast Vlan Igmp SettingsMulticast Igmp Snooping Igmp GlobalMulticast Bridge Multicast Forward All Multicast Bridge MulticastSnmp Views Snmp Global ParametersSnmp Group Profile Snmp Group MembershipUser Name Provides a user-defined local user list Snmp Communities Snmp Notification Recipient Snmp Notification FilterBase Table Advanced TableAdmin User Authentication AdminUser Authentication Local User EditAdmin Dynamic Address Admin Static AddressSecure The entry is defined for locked ports Clear Table If selected, this clears the MAC Address tableAdmin Port Mirroring Admin Cable TestQuery Admin Save Configuration Admin Firmware Upgrade Admin RebootAdmin Factory Default Admin Logging Admin Server LogsAdmin Memory Logs Logout Admin Flash LogsAppendix a About Gigabit Ethernet Fiber Optic Cabling Appendix aGigabit Ethernet Fiber Optic CablingAbout Switch Stacking Appendix B About Switch StackingAppendix B Stack Building Quick StartStack Resiliency Advanced StackingUnit IDs Unit ID AllocationStack Units Startup Process Master DiscoveryMaster Election User Controls Unit and Port ConfigurationStacking Examples Replacing a Failed Stack Member in a Running StackStack Master Failure and Replacement Splitting a Stack Subgroup Contains Both Master Unit and Backup Master UnitBoth Stacks Kept Running During Insertion Merging Two StacksInserting Too Many Units Stacking Cable FailureAppendix C Appendix C GlossaryGlossary Glossary Mail protocol on the Internet Packet a unit of data sent over a networkAppendix C Appendix D Specifications SpecificationsAppendix D Unit Weight SLM224G4S 1,927 kg Dimensions802.3 10BASE-T Ethernet 802.3z Gigabit EthernetLimited Warranty Warranty InformationObtaining Warranty Service Appendix ETechnical Support Warranty InformationRegulatory Information Appendix FRegulatory Information Appendix F Norsk Norwegian Miljøinformasjon for kunder i EU Appendix F Contact Information Appendix G8012510A-AI