Linksys SLM248G4S (G5) manual Chapter Configuration Using Console Interface, Using telnet

Page 14

Chapter 4

Chapter 4:

Configuration Using the

Console Interface

Overview

The Switch features a menu-driven console interface that lets you perform basic switch configuration and easily manage your network. To use the console interface, you either run the HyperTerminal application to configure a serial connection through the Switch’s console port, or run a telnet session over an Ethernet connection.

Using the HyperTerminal Application

To access the console interface using HyperTerminal:

1.Click the Start button.

2.SelectAllPrograms>Accessories>Communications > HyperTerminal.

Start > All Programs > Accessories > Communications > HyperTerminal

3.Enter a name for this connection. Select an icon for the application, then click OK.

HyperTerminal Connection Description Screen

4.Select a port to communicate with the switch. Select COM1 or COM2.

Installation

5.Set the serial port settings as follows, then click OK. Bits per Second: 38400

Databits: 8

Parity: None

Stop bits: 1

Flow control: None

HyperTerminal Properties Screen

6.The Login screen appears. Proceed to the “Login” section below.

Using telnet

In addition to using HyperTerminal to operate the console interface through the Switch’s console port, you can also use a telnet session to operate the console interface through an Ethernet connection.

1.Click Start, then select All Programs > Accessories > Command Prompt to open a command prompt.

2.At the prompt, enter telnet 192.168.1.254, then press Enter.

3.The Login screen appears. Proceed to the “Login” section below.

HyperTerminal Connect To Screen

24/48-Port 10/100 + 4-Port Gigabit Resilient Clustering Smart Switch with 2 Combo SFPs

Image 14

Contents Port or 48-Port 10/100 + Icon Descriptions About This GuideAbout This Guide Online ResourcesTable of Contents Snmp Gigabit Ethernet Fiber Optic Cabling Appendix B About Switch StackingAppendix C Glossary Appendix F Regulatory Information Appendix D SpecificationsAppendix E Warranty Information Appendix G Contact InformationChapter IntroductionFront Panel Chapter Product OverviewProduct Overview Back PanelSLM248G4S Pre-Installation Considerations Chapter InstallationInstallation Placement OptionsRack-Mount Placement Hardware InstallationDesktop Placement Uplinking the Switch Configuring Stacking ModeConnect port G1 on Unit 3 to port G2 on Unit Replacing a Stacked SwitchConnect port G1 on Unit 2 to port G2 on Unit Using telnet Chapter Configuration Using Console InterfaceUsing the HyperTerminal Application Login screen appears. Proceed to the Login section belowSwitch Main Menu How to Use the Console InterfaceLogin System Configuration MenuSystem Information Management SettingsUser & Password Settings Security Settings IP ConfigurationNetwork Configuration File ManagementStack Configuration Restore System Default SettingsReboot System Port Status Port ConfigurationSystem Mode HelpSetup Summary Chapter Configuration Using Web-based UtilitySetup Device InformationDefault Gateway The IP address default 0.0.0.0 Setup ZoomSetup Network Settings DNS Server The IP address of your ISP’s server thatLocal Time Setup TimeIdentification Daylight SavingPort Management Setup Stack ManagementPort Management Port Settings Sntp ServersPort Configuration LAG Configuration Port Management Link AggregationGlobal Parameter Lacp screen contains fields for configuring Lacp LAGsPort Management Lacp Port PriorityVlan Management Create Vlan Vlan Management Port SettingsVlan Management Lacp Port TableJoin Vlan to Port Vlan Management Port to VlanVlan Management Vlan to Port Statistics Statistics Rmon StatisticsLog Table Statistics Rmon HistoryRmon History Rmon History TableStatistics Rmon Alarms Add AlarmStatistics Interface Statistics Statistics Port UtilizationStatistics Rmon Events Interface Security 802.1x SettingsSecurity Ethernet-likeSetting Timer Security Port SecuritySecurity Management Access List Web IP FilteringBroadcast Only Counts only Broadcast traffic Security Storm ControlSecurity Radius CoS Default QoS CoS SettingsCoS Settings CoS Settings screen is used to enable or disable CoSQoS Bandwidth QoS Queue SettingsQoS Dscp Settings Spanning Tree STP Status QoS Basic ModeSpanning Tree Bridge Settings Spanning Tree STP Port SettingsGlobal Setting Spanning Tree Global STPMulticast Igmp Snooping Vlan Igmp SettingsMulticast Igmp GlobalMulticast Bridge Multicast Multicast Bridge Multicast Forward AllSnmp Global Parameters Snmp ViewsUser Name Provides a user-defined local user list Snmp Group ProfileSnmp Group Membership Snmp Communities Base Table Snmp Notification FilterSnmp Notification Recipient Advanced TableUser Authentication AdminAdmin User Authentication Local User EditSecure The entry is defined for locked ports Admin Static AddressAdmin Dynamic Address Clear Table If selected, this clears the MAC Address tableQuery Admin Port MirroringAdmin Cable Test Admin Save Configuration Admin Factory Default Admin Firmware UpgradeAdmin Reboot Admin Memory Logs Admin LoggingAdmin Server Logs Admin Flash Logs LogoutGigabit Ethernet Appendix aAppendix a About Gigabit Ethernet Fiber Optic Cabling Fiber Optic CablingAppendix B Appendix B About Switch StackingAbout Switch Stacking Stack Building Quick StartUnit IDs Advanced StackingStack Resiliency Unit ID AllocationMaster Election Stack Units Startup ProcessMaster Discovery Stacking Examples Unit and Port ConfigurationUser Controls Replacing a Failed Stack Member in a Running StackStack Master Failure and Replacement Subgroup Contains Both Master Unit and Backup Master Unit Splitting a StackMerging Two Stacks Both Stacks Kept Running During InsertionStacking Cable Failure Inserting Too Many UnitsGlossary Appendix CAppendix C Glossary Glossary Packet a unit of data sent over a network Mail protocol on the InternetAppendix C Appendix D Appendix D SpecificationsSpecifications 802.3 10BASE-T Ethernet DimensionsUnit Weight SLM224G4S 1,927 kg 802.3z Gigabit EthernetObtaining Warranty Service Warranty InformationLimited Warranty Appendix EWarranty Information Technical SupportAppendix F Regulatory InformationRegulatory Information Appendix F Norsk Norwegian Miljøinformasjon for kunder i EU Appendix F Appendix G Contact Information8012510A-AI