Manuals / Edimax Technology / Computer Equipment / Server

Edimax Technology PS-1206MF Login, Note Default User Name is “admin”, default password is “1234”

Models: PS-1206MF PS-1206MFG

1 61

Download 61 pages 57.98 Kb

Page 41

6.2Login

6.2Login

You may use any Web Browser to review the status or configure the settings of the MFP Server. After entering the IP address of the MFP Server, a login page displays. You have to enter the correct “User Name” and “Password” before going to the Web Management pages.

Note: Default User Name is “admin”, default password is “1234”.

30

Image 41

Edimax Technology PS-1206MFG manual Login, Note Default User Name is “admin”, default password is “1234”

Contents

Page Page FCC Warning Federal Communication Commission Interference StatementRadio Frequency Interference Requirements Federal Communication Commission FCC Radiation Exposure StatementCountry Code Setting Disable RSS-210 Compliance StatementTransmitter Antenna IC Radiation Exposure StatementSafety R&TTE Compliance StatementEU Countries Intended for Use CE Mark WarningRegulatory Approvals for AC Adapter Safety Information Do not expose the device to dampness, dust or corrosive liquids Make sure to connect the cables to the correct ports5. Server Configuration in MAC 3. Using Your All-in-one in MAC4. MFP Manager in MAC IntroductionLoad Default 7. TroubleshootingUpgrade Firmware 6.5.11. Introduction All-in-one MFP Server Mode 2. MFP Server ModesChapter 9 IPP Printing Not in MAC MFP Server ModeChapter 7 LPR Printing Chapter 8 RAW Printing 3. Using Your All-in-one in MAC Page 3.1 Printing An example EPSON CX-8400/9400 Series Utilities 3.2 ScanningMAC Scanning Utility 3.3 Reading Memory Cards 4.1 MFP Server List 4. MFP Manager in MACMFP Server List MFP Server List 4.2.1 General Setting 4.2 Option Settings4.2.2 Search for MFP Server 5.1 Introduction 5. Server Configuration in MAC5.2 Search for All Available MFP Server 5.3 Status of MFP Server You can refresh the MFP Server’s status by click the “Refresh” button 5.4 General Setting You can configure the “Server Name”, “User Name” and “Password” here IP Address Subnet Mask 5.5 TCP/IP ConfigurationIP Address Assignment 5.6 System Configuration 5.7 Wireless Configuration You have to go through the following security setting procedure wireless connectionWEP Security Mode p.s. this picture is temporary we will post the formal one later WPA-PSK/WPA2-PSK Security Mode Page IP Address User Name Admin Password 6. Web Management6.1 Introduction Note Default User Name is “admin”, default password is “1234” 6.2 Login6.3.1 System Status 6.3 Device Status6.3.2 Printer Status 6.3.3 TCP/IP Status 6.4.1.1 Admin Password 6.4 Setup Wizard6.4.1 System Re-type Password enter the same password for the MFP Server again You can change the MFP Server name and password from hereSome advanced feature of the MFP Server can be set here 6.4.1.2 Advanced Settings6.4.2 Wireless wireless LAN mode. The MFP Server default is in “Auto” mode 6.4.2.1 Site Survey 6.4.2.2 Encryption This MFP Server supports WEP and WPA-PSK security mode. If you want to use WEP encryption to protect your wireless network, you have to select “WEP”. If you want to use WPA-PSK, you have to select “WPA-PSK” for an infrastructure network or “WPA-None” enables WPA security for an ad hoc network. The wireless security setting should match other wireless devices in the same networkWEP Security Mode 64-bit WEP input 10-digit Hex values in the A-F, a-f and 0-9 range or WPA-PSK Mode WPA2-PSK Mode Security Mode 6.4.3 TCP/IP 6.4.4 Save Settings 6.5 System Tools 6.5.1 Load Default6.5.2 Upgrade Firmware 7. Troubleshooting 2. Add “mfpagent.exe” program to the exception list 1. Add the “servoap.exe” program to the exception list