Manuals / Edimax Technology / Computer Equipment / Server

Edimax Technology PS-1206MFG manual RSS-210 Compliance Statement, Transmitter Antenna

Models: PS-1206MF PS-1206MFG

1 61

Download 61 pages 57.98 Kb

Page 5

RSS-210 Compliance Statement

The term “IC:” before the certification/registration number only signifies that Industry Canada technical specifications were met. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Transmitter Antenna

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication

This device has been designed to operate with an antenna having a maximum gain of 5dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

Country Code Setting Disable

Country Code selection feature to be disabled for products marketed to the US/CANADA.

Image 5

Edimax Technology PS-1206MFG manual RSS-210 Compliance Statement, Transmitter Antenna, IC Radiation Exposure Statement

Contents

Page Page FCC Warning Federal Communication Commission Interference StatementRadio Frequency Interference Requirements Federal Communication Commission FCC Radiation Exposure StatementCountry Code Setting Disable RSS-210 Compliance StatementTransmitter Antenna IC Radiation Exposure StatementSafety R&TTE Compliance StatementEU Countries Intended for Use CE Mark WarningRegulatory Approvals for AC Adapter Safety Information Do not expose the device to dampness, dust or corrosive liquids Make sure to connect the cables to the correct ports5. Server Configuration in MAC 3. Using Your All-in-one in MAC4. MFP Manager in MAC IntroductionLoad Default 7. TroubleshootingUpgrade Firmware 6.5.11. Introduction All-in-one MFP Server Mode 2. MFP Server ModesChapter 9 IPP Printing Not in MAC MFP Server ModeChapter 7 LPR Printing Chapter 8 RAW Printing 3. Using Your All-in-one in MAC Page 3.1 Printing An example EPSON CX-8400/9400 Series Utilities 3.2 ScanningMAC Scanning Utility 3.3 Reading Memory Cards 4.1 MFP Server List 4. MFP Manager in MACMFP Server List MFP Server List 4.2.1 General Setting 4.2 Option Settings4.2.2 Search for MFP Server 5.1 Introduction 5. Server Configuration in MAC5.2 Search for All Available MFP Server 5.3 Status of MFP Server You can refresh the MFP Server’s status by click the “Refresh” button 5.4 General Setting You can configure the “Server Name”, “User Name” and “Password” here IP Address Subnet Mask 5.5 TCP/IP ConfigurationIP Address Assignment 5.6 System Configuration 5.7 Wireless Configuration You have to go through the following security setting procedure wireless connectionWEP Security Mode p.s. this picture is temporary we will post the formal one later WPA-PSK/WPA2-PSK Security Mode Page IP Address User Name Admin Password 6. Web Management6.1 Introduction Note Default User Name is “admin”, default password is “1234” 6.2 Login6.3.1 System Status 6.3 Device Status6.3.2 Printer Status 6.3.3 TCP/IP Status 6.4.1.1 Admin Password 6.4 Setup Wizard6.4.1 System Re-type Password enter the same password for the MFP Server again You can change the MFP Server name and password from hereSome advanced feature of the MFP Server can be set here 6.4.1.2 Advanced Settings6.4.2 Wireless wireless LAN mode. The MFP Server default is in “Auto” mode 6.4.2.1 Site Survey 6.4.2.2 Encryption This MFP Server supports WEP and WPA-PSK security mode. If you want to use WEP encryption to protect your wireless network, you have to select “WEP”. If you want to use WPA-PSK, you have to select “WPA-PSK” for an infrastructure network or “WPA-None” enables WPA security for an ad hoc network. The wireless security setting should match other wireless devices in the same networkWEP Security Mode 64-bit WEP input 10-digit Hex values in the A-F, a-f and 0-9 range or WPA-PSK Mode WPA2-PSK Mode Security Mode 6.4.3 TCP/IP 6.4.4 Save Settings 6.5 System Tools 6.5.1 Load Default6.5.2 Upgrade Firmware 7. Troubleshooting 2. Add “mfpagent.exe” program to the exception list 1. Add the “servoap.exe” program to the exception list