Manuals / Edimax Technology / Computer Equipment / Server

Edimax Technology PS-1206MFG manual Upgrade Firmware

Models: PS-1206MF PS-1206MFG

1 61

Download 61 pages 57.98 Kb

Page 58

6.5.2Upgrade Firmware

6.5.2Upgrade Firmware

You can upgrade new firmware for this MFP Server in this page. Click “Browse” to select the new firmware, and then click “OK”. The firmware will be updated in several minutes.

Be aware that if you have started upgrading firmware, you have to follow all the upgrading steps or the MFP Server can’t return to normal configuration.

47

Image 58

Edimax Technology PS-1206MFG manual Upgrade Firmware

Contents

Page Page Federal Communication Commission Interference Statement FCC WarningFederal Communication Commission FCC Radiation Exposure Statement Radio Frequency Interference RequirementsTransmitter Antenna RSS-210 Compliance StatementCountry Code Setting Disable IC Radiation Exposure StatementEU Countries Intended for Use R&TTE Compliance StatementSafety CE Mark WarningRegulatory Approvals for AC Adapter Safety Information Make sure to connect the cables to the correct ports Do not expose the device to dampness, dust or corrosive liquids4. MFP Manager in MAC 3. Using Your All-in-one in MAC5. Server Configuration in MAC IntroductionUpgrade Firmware 7. TroubleshootingLoad Default 6.5.11. Introduction 2. MFP Server Modes All-in-one MFP Server ModeChapter 7 LPR Printing Chapter 8 RAW Printing MFP Server ModeChapter 9 IPP Printing Not in MAC 3. Using Your All-in-one in MAC Page 3.1 Printing 3.2 Scanning An example EPSON CX-8400/9400 Series UtilitiesMAC Scanning Utility 3.3 Reading Memory Cards 4. MFP Manager in MAC 4.1 MFP Server ListMFP Server List MFP Server List 4.2 Option Settings 4.2.1 General Setting4.2.2 Search for MFP Server 5. Server Configuration in MAC 5.1 Introduction5.2 Search for All Available MFP Server 5.3 Status of MFP Server You can refresh the MFP Server’s status by click the “Refresh” button 5.4 General Setting You can configure the “Server Name”, “User Name” and “Password” here IP Address Assignment 5.5 TCP/IP ConfigurationIP Address Subnet Mask 5.6 System Configuration 5.7 Wireless Configuration wireless connection You have to go through the following security setting procedureWEP Security Mode p.s. this picture is temporary we will post the formal one later WPA-PSK/WPA2-PSK Security Mode Page 6.1 Introduction 6. Web ManagementIP Address User Name Admin Password 6.2 Login Note Default User Name is “admin”, default password is “1234”6.3 Device Status 6.3.1 System Status6.3.2 Printer Status 6.3.3 TCP/IP Status 6.4.1 System 6.4 Setup Wizard6.4.1.1 Admin Password You can change the MFP Server name and password from here Re-type Password enter the same password for the MFP Server again6.4.1.2 Advanced Settings Some advanced feature of the MFP Server can be set here6.4.2 Wireless wireless LAN mode. The MFP Server default is in “Auto” mode 6.4.2.1 Site Survey WEP Security Mode This MFP Server supports WEP and WPA-PSK security mode. If you want to use WEP encryption to protect your wireless network, you have to select “WEP”. If you want to use WPA-PSK, you have to select “WPA-PSK” for an infrastructure network or “WPA-None” enables WPA security for an ad hoc network. The wireless security setting should match other wireless devices in the same network6.4.2.2 Encryption 64-bit WEP input 10-digit Hex values in the A-F, a-f and 0-9 range or WPA-PSK Mode WPA2-PSK Mode Security Mode 6.4.3 TCP/IP 6.4.4 Save Settings 6.5.1 Load Default 6.5 System Tools6.5.2 Upgrade Firmware 7. Troubleshooting 1. Add the “servoap.exe” program to the exception list 2. Add “mfpagent.exe” program to the exception list