Manuals / Edimax Technology / Computer Equipment / Server

Edimax Technology PS-1206MFG manual 6.3.3 TCP/IP Status

Models: PS-1206MF PS-1206MFG

1 61

Download 61 pages 57.98 Kb

Page 44

6.3.3TCP/IP Status

6.3.3TCP/IP Status

This page lists all TCP/IP settings of the MFP Server including “IP Address”, “Subnet Mask” and “Gateway”. It also can tell whether the DHCP server is “On” or “Off”.

33

Image 44

Edimax Technology PS-1206MFG manual 6.3.3 TCP/IP Status

Contents

Page Page Federal Communication Commission Interference Statement FCC WarningFederal Communication Commission FCC Radiation Exposure Statement Radio Frequency Interference RequirementsRSS-210 Compliance Statement Country Code Setting DisableTransmitter Antenna IC Radiation Exposure StatementR&TTE Compliance Statement SafetyEU Countries Intended for Use CE Mark WarningRegulatory Approvals for AC Adapter Safety Information Make sure to connect the cables to the correct ports Do not expose the device to dampness, dust or corrosive liquids3. Using Your All-in-one in MAC 5. Server Configuration in MAC4. MFP Manager in MAC Introduction7. Troubleshooting Load DefaultUpgrade Firmware 6.5.11. Introduction 2. MFP Server Modes All-in-one MFP Server ModeChapter 9 IPP Printing Not in MAC MFP Server ModeChapter 7 LPR Printing Chapter 8 RAW Printing 3. Using Your All-in-one in MAC Page 3.1 Printing 3.2 Scanning An example EPSON CX-8400/9400 Series UtilitiesMAC Scanning Utility 3.3 Reading Memory Cards 4. MFP Manager in MAC 4.1 MFP Server ListMFP Server List MFP Server List 4.2 Option Settings 4.2.1 General Setting4.2.2 Search for MFP Server 5. Server Configuration in MAC 5.1 Introduction5.2 Search for All Available MFP Server 5.3 Status of MFP Server You can refresh the MFP Server’s status by click the “Refresh” button 5.4 General Setting You can configure the “Server Name”, “User Name” and “Password” here IP Address Subnet Mask 5.5 TCP/IP ConfigurationIP Address Assignment 5.6 System Configuration 5.7 Wireless Configuration wireless connection You have to go through the following security setting procedureWEP Security Mode p.s. this picture is temporary we will post the formal one later WPA-PSK/WPA2-PSK Security Mode Page IP Address User Name Admin Password 6. Web Management6.1 Introduction 6.2 Login Note Default User Name is “admin”, default password is “1234”6.3 Device Status 6.3.1 System Status6.3.2 Printer Status 6.3.3 TCP/IP Status 6.4.1.1 Admin Password 6.4 Setup Wizard6.4.1 System You can change the MFP Server name and password from here Re-type Password enter the same password for the MFP Server again6.4.1.2 Advanced Settings Some advanced feature of the MFP Server can be set here6.4.2 Wireless wireless LAN mode. The MFP Server default is in “Auto” mode 6.4.2.1 Site Survey 6.4.2.2 Encryption This MFP Server supports WEP and WPA-PSK security mode. If you want to use WEP encryption to protect your wireless network, you have to select “WEP”. If you want to use WPA-PSK, you have to select “WPA-PSK” for an infrastructure network or “WPA-None” enables WPA security for an ad hoc network. The wireless security setting should match other wireless devices in the same networkWEP Security Mode 64-bit WEP input 10-digit Hex values in the A-F, a-f and 0-9 range or WPA-PSK Mode WPA2-PSK Mode Security Mode 6.4.3 TCP/IP 6.4.4 Save Settings 6.5.1 Load Default 6.5 System Tools6.5.2 Upgrade Firmware 7. Troubleshooting 1. Add the “servoap.exe” program to the exception list 2. Add “mfpagent.exe” program to the exception list