Manuals / Edimax Technology / Computer Equipment / Server

Edimax Technology PS-1206MFG manual Advanced Settings

Models: PS-1206MF PS-1206MFG

1 61

Download 61 pages 57.98 Kb

Page 47

6.4.1.2Advanced Settings

6.4.1.2Advanced Settings

Some advanced feature of the MFP Server can be set here.

TCP/IP Printing (LPR/IPP/RAW): The MFP Server supports TCP/IP network protocol and LPR/IPP/RAW printing protocols. By default these protocols are enabled.

36

Image 47

Edimax Technology PS-1206MFG manual Advanced Settings, Some advanced feature of the MFP Server can be set here

Contents

Page Page FCC Warning Federal Communication Commission Interference StatementRadio Frequency Interference Requirements Federal Communication Commission FCC Radiation Exposure StatementIC Radiation Exposure Statement RSS-210 Compliance StatementCountry Code Setting Disable Transmitter AntennaCE Mark Warning R&TTE Compliance StatementSafety EU Countries Intended for UseRegulatory Approvals for AC Adapter Safety Information Do not expose the device to dampness, dust or corrosive liquids Make sure to connect the cables to the correct portsIntroduction 3. Using Your All-in-one in MAC5. Server Configuration in MAC 4. MFP Manager in MAC6.5.1 7. TroubleshootingLoad Default Upgrade Firmware1. Introduction All-in-one MFP Server Mode 2. MFP Server ModesChapter 9 IPP Printing Not in MAC MFP Server ModeChapter 7 LPR Printing Chapter 8 RAW Printing 3. Using Your All-in-one in MAC Page 3.1 Printing An example EPSON CX-8400/9400 Series Utilities 3.2 ScanningMAC Scanning Utility 3.3 Reading Memory Cards 4.1 MFP Server List 4. MFP Manager in MACMFP Server List MFP Server List 4.2.1 General Setting 4.2 Option Settings4.2.2 Search for MFP Server 5.1 Introduction 5. Server Configuration in MAC5.2 Search for All Available MFP Server 5.3 Status of MFP Server You can refresh the MFP Server’s status by click the “Refresh” button 5.4 General Setting You can configure the “Server Name”, “User Name” and “Password” here IP Address Subnet Mask 5.5 TCP/IP ConfigurationIP Address Assignment 5.6 System Configuration 5.7 Wireless Configuration You have to go through the following security setting procedure wireless connectionWEP Security Mode p.s. this picture is temporary we will post the formal one later WPA-PSK/WPA2-PSK Security Mode Page IP Address User Name Admin Password 6. Web Management6.1 Introduction Note Default User Name is “admin”, default password is “1234” 6.2 Login6.3.1 System Status 6.3 Device Status6.3.2 Printer Status 6.3.3 TCP/IP Status 6.4.1.1 Admin Password 6.4 Setup Wizard6.4.1 System Re-type Password enter the same password for the MFP Server again You can change the MFP Server name and password from hereSome advanced feature of the MFP Server can be set here 6.4.1.2 Advanced Settings6.4.2 Wireless wireless LAN mode. The MFP Server default is in “Auto” mode 6.4.2.1 Site Survey WEP Security Mode This MFP Server supports WEP and WPA-PSK security mode. If you want to use WEP encryption to protect your wireless network, you have to select “WEP”. If you want to use WPA-PSK, you have to select “WPA-PSK” for an infrastructure network or “WPA-None” enables WPA security for an ad hoc network. The wireless security setting should match other wireless devices in the same network6.4.2.2 Encryption 64-bit WEP input 10-digit Hex values in the A-F, a-f and 0-9 range or WPA-PSK Mode WPA2-PSK Mode Security Mode 6.4.3 TCP/IP 6.4.4 Save Settings 6.5 System Tools 6.5.1 Load Default6.5.2 Upgrade Firmware 7. Troubleshooting 2. Add “mfpagent.exe” program to the exception list 1. Add the “servoap.exe” program to the exception list