Manuals / Edimax Technology / Computer Equipment / Server

Edimax Technology PS-1206MFG manual Search for MFP Server

Models: PS-1206MF PS-1206MFG

1 61

Download 61 pages 57.98 Kb

Page 25

4.2.2Search for MFP Server

4.2.2Search for MFP Server

If MFP Server is not in the same network as your computer, you can enter the IP Address of the MFP Server to do remote search. The MFP Server in the “Remote MFP Server List” will be added to the “MFP Server List” for you to configure.

Note:

If the remote MFP Server you have searched is behind a NAT Router, the MFP Server may not operate normally.

14

Image 25

Edimax Technology PS-1206MFG manual Search for MFP Server

Contents

Page Page FCC Warning Federal Communication Commission Interference StatementRadio Frequency Interference Requirements Federal Communication Commission FCC Radiation Exposure StatementCountry Code Setting Disable RSS-210 Compliance StatementTransmitter Antenna IC Radiation Exposure StatementSafety R&TTE Compliance StatementEU Countries Intended for Use CE Mark WarningRegulatory Approvals for AC Adapter Safety Information Do not expose the device to dampness, dust or corrosive liquids Make sure to connect the cables to the correct ports5. Server Configuration in MAC 3. Using Your All-in-one in MAC4. MFP Manager in MAC IntroductionLoad Default 7. TroubleshootingUpgrade Firmware 6.5.11. Introduction All-in-one MFP Server Mode 2. MFP Server ModesChapter 7 LPR Printing Chapter 8 RAW Printing MFP Server ModeChapter 9 IPP Printing Not in MAC 3. Using Your All-in-one in MAC Page 3.1 Printing An example EPSON CX-8400/9400 Series Utilities 3.2 ScanningMAC Scanning Utility 3.3 Reading Memory Cards 4.1 MFP Server List 4. MFP Manager in MACMFP Server List MFP Server List 4.2.1 General Setting 4.2 Option Settings4.2.2 Search for MFP Server 5.1 Introduction 5. Server Configuration in MAC5.2 Search for All Available MFP Server 5.3 Status of MFP Server You can refresh the MFP Server’s status by click the “Refresh” button 5.4 General Setting You can configure the “Server Name”, “User Name” and “Password” here IP Address Assignment 5.5 TCP/IP ConfigurationIP Address Subnet Mask 5.6 System Configuration 5.7 Wireless Configuration You have to go through the following security setting procedure wireless connectionWEP Security Mode p.s. this picture is temporary we will post the formal one later WPA-PSK/WPA2-PSK Security Mode Page 6.1 Introduction 6. Web ManagementIP Address User Name Admin Password Note Default User Name is “admin”, default password is “1234” 6.2 Login6.3.1 System Status 6.3 Device Status6.3.2 Printer Status 6.3.3 TCP/IP Status 6.4.1 System 6.4 Setup Wizard6.4.1.1 Admin Password Re-type Password enter the same password for the MFP Server again You can change the MFP Server name and password from hereSome advanced feature of the MFP Server can be set here 6.4.1.2 Advanced Settings6.4.2 Wireless wireless LAN mode. The MFP Server default is in “Auto” mode 6.4.2.1 Site Survey WEP Security Mode This MFP Server supports WEP and WPA-PSK security mode. If you want to use WEP encryption to protect your wireless network, you have to select “WEP”. If you want to use WPA-PSK, you have to select “WPA-PSK” for an infrastructure network or “WPA-None” enables WPA security for an ad hoc network. The wireless security setting should match other wireless devices in the same network6.4.2.2 Encryption 64-bit WEP input 10-digit Hex values in the A-F, a-f and 0-9 range or WPA-PSK Mode WPA2-PSK Mode Security Mode 6.4.3 TCP/IP 6.4.4 Save Settings 6.5 System Tools 6.5.1 Load Default6.5.2 Upgrade Firmware 7. Troubleshooting 2. Add “mfpagent.exe” program to the exception list 1. Add the “servoap.exe” program to the exception list