Linksys SLM248G4S (G5), SLM224G4S (G5) manual QoS CoS Settings, CoS Default

Page 38

Chapter 5

Configuration Using the Web-based Utility

Usage Type  This is the RADIUS server authentication type. The possible values are:

•Login  (Default value) Indicates that the RADIUS server is used for authenticating user name and passwords.

•802.1X  Indicates that the RADIUS server is used for 802.1X authentication.

•All  Indicates that the RADIUS server is used for authenticating user name and passwords, and 802.1X port authentication.

Click Add to List to add the RADIUS configuration to the RADIUS table at the bottom of the screen.

Click Save Settings to save the changes, or Cancel Changes to cancel the changes.

QoS

Network traffic is usually unpredictable, and the only basic assurance that can be offered is best effort traffic delivery. To overcome this challenge, Quality of Service (QoS) is applied throughout the network. This ensures that network traffic is prioritized according to specified criteria, and that specific traffic receives preferential treatment. QoS in the network optimizes network performance and entails two basic facilities:

Classifying incoming traffic into handling classes, based on an attribute, including:

•The ingress interface

•Packet content

•A combination of these attributes

Providing various mechanisms for determining the allocation of network resources to different handling classes, including:

•The assignment of network traffic to a particular hardware queue

•The assignment of internal resources

•Traffic shaping

The terms Class of Service (CoS) and QoS are used in the following context:

•CoS provides varying Layer 2 traffic services. CoS refers to classifying traffic into traffic classes, where each class is handled as an aggregate whole, with no per-flow settings. CoS is usually related to the 802.1p service that classifies flows according to their Layer 2 priority, as set in the VLAN header.

•QoS refers to Layer 2 traffic and above. QoS handles per-flow settings, even within a single traffic class.

The QoS configuration options are CoS Settings, Queue Settings, DSCP Settings, and Basic Mode.

QoS > CoS Settings

The CoS Settings screen is used to enable or disable CoS.

QoS > CoS Settings

CoS Settings

QoS Mode  Indicates if QoS is enabled. The possible values are:

•Disable  Disables QoS.

•Basic  Enables QoS. This is the default value.

Class of Service  Specifies the CoS priority tag values, where 0 is the lowest and 7 is the highest.

Queue  Defines the traffic forwarding queue to which the CoS priority is mapped. Four traffic priority queues are supported.

Click Restore Defaults to restore the device factory defaults for mapping CoS values to a forwarding queue.

CoS Default

Unit No.  The unit to which the CoS configuration applies.

Default CoS  Determines the default CoS value for incoming packets for which a VLAN tag is not defined. The possible field values are 0-7. The default CoS is 0.

LAG  The LAG to which the port belongs, if relevant. If the port is a member of a LAG, the LAG settings override the port settings.

Click Save Settings to save the changes, or Cancel Changes to cancel the changes.

24/48-Port 10/100 + 4-Port Gigabit Resilient Clustering Smart Switch with 2 Combo SFPs

32

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Port or 48-Port 10/100 + Icon Descriptions About This GuideAbout This Guide Online ResourcesTable of Contents Snmp Gigabit Ethernet Fiber Optic Cabling Appendix B About Switch StackingAppendix C Glossary Appendix F Regulatory Information Appendix D SpecificationsAppendix E Warranty Information Appendix G Contact InformationChapter IntroductionFront Panel Chapter Product OverviewProduct Overview Back PanelSLM248G4S Pre-Installation Considerations Chapter InstallationInstallation Placement OptionsRack-Mount Placement Hardware InstallationDesktop Placement Uplinking the Switch Configuring Stacking ModeConnect port G1 on Unit 3 to port G2 on Unit Replacing a Stacked SwitchConnect port G1 on Unit 2 to port G2 on Unit Using telnet Chapter Configuration Using Console InterfaceUsing the HyperTerminal Application Login screen appears. Proceed to the Login section belowSwitch Main Menu How to Use the Console InterfaceLogin System Configuration MenuSystem Information Management SettingsUser & Password Settings Security Settings IP ConfigurationNetwork Configuration File ManagementStack Configuration Restore System Default SettingsReboot System Port Status Port ConfigurationSystem Mode HelpSetup Summary Chapter Configuration Using Web-based UtilitySetup Device InformationDefault Gateway The IP address default 0.0.0.0 Setup ZoomSetup Network Settings DNS Server The IP address of your ISP’s server thatLocal Time Setup TimeIdentification Daylight SavingPort Management Setup Stack ManagementPort Management Port Settings Sntp ServersPort Configuration LAG Configuration Port Management Link AggregationGlobal Parameter Lacp screen contains fields for configuring Lacp LAGsPort Management Lacp Port PriorityVlan Management Create Vlan Vlan Management Port SettingsVlan Management Lacp Port TableJoin Vlan to Port Vlan Management Port to VlanVlan Management Vlan to Port Statistics Statistics Rmon StatisticsLog Table Statistics Rmon HistoryRmon History Rmon History TableStatistics Rmon Alarms Add AlarmStatistics Interface Statistics Statistics Port UtilizationStatistics Rmon Events Interface Security 802.1x SettingsSecurity Ethernet-likeSetting Timer Security Port SecuritySecurity Management Access List Web IP FilteringBroadcast Only Counts only Broadcast traffic Security Storm ControlSecurity Radius CoS Default QoS CoS SettingsCoS Settings CoS Settings screen is used to enable or disable CoSQoS Bandwidth QoS Queue SettingsQoS Dscp Settings Spanning Tree STP Status QoS Basic ModeSpanning Tree Bridge Settings Spanning Tree STP Port SettingsGlobal Setting Spanning Tree Global STPMulticast Igmp Snooping Vlan Igmp SettingsMulticast Igmp GlobalMulticast Bridge Multicast Multicast Bridge Multicast Forward AllSnmp Global Parameters Snmp ViewsUser Name Provides a user-defined local user list Snmp Group ProfileSnmp Group Membership Snmp Communities Base Table Snmp Notification FilterSnmp Notification Recipient Advanced TableUser Authentication AdminAdmin User Authentication Local User EditSecure The entry is defined for locked ports Admin Static AddressAdmin Dynamic Address Clear Table If selected, this clears the MAC Address tableQuery Admin Port MirroringAdmin Cable Test Admin Save Configuration Admin Factory Default Admin Firmware UpgradeAdmin Reboot Admin Memory Logs Admin LoggingAdmin Server Logs Admin Flash Logs LogoutGigabit Ethernet Appendix aAppendix a About Gigabit Ethernet Fiber Optic Cabling Fiber Optic CablingAppendix B Appendix B About Switch StackingAbout Switch Stacking Stack Building Quick StartUnit IDs Advanced StackingStack Resiliency Unit ID AllocationMaster Election Stack Units Startup ProcessMaster Discovery Stacking Examples Unit and Port ConfigurationUser Controls Replacing a Failed Stack Member in a Running StackStack Master Failure and Replacement Subgroup Contains Both Master Unit and Backup Master Unit Splitting a StackMerging Two Stacks Both Stacks Kept Running During InsertionStacking Cable Failure Inserting Too Many UnitsGlossary Appendix CAppendix C Glossary Glossary Packet a unit of data sent over a network Mail protocol on the InternetAppendix C Appendix D Appendix D SpecificationsSpecifications 802.3 10BASE-T Ethernet DimensionsUnit Weight SLM224G4S 1,927 kg 802.3z Gigabit EthernetObtaining Warranty Service Warranty InformationLimited Warranty Appendix EWarranty Information Technical SupportAppendix F Regulatory InformationRegulatory Information Appendix F Norsk Norwegian Miljøinformasjon for kunder i EU Appendix F Appendix G Contact Information8012510A-AI
Top Page Image Contents