Advantech PCI-1710 user manual Installation Instructions

Page 15

2.3 Installation Instructions

The PCI-1710/1710HG can be installed in any PCI slot in the computer. However, refer to the computer user's manual to avoid any mistakes and danger before you follow the installation procedure below:

1.Turn off your computer and any accessories connected to the computer.

Warning! TURN OFF your computer power supply whenever you install or remove any card, or connect and disconnect cables.

2.Disconnect the power cord and any other cables from the back of the computer.

3.Remove the cover of the computer.

4.Select an empty 5 V PCI slot. Remove the screw that secures the expansion slot cover to the system unit. Save the screw to secure the interface card retaining bracket.

5.Carefully grasp the upper edge of the PCI-1710/1710HG. Align the hole in the retaining bracket with the hole on the expansion slot and align the gold striped edge connector with the expansion slot socket. Press the card into the socket gently but firmly. Make sure the card fits the slot tightly.

6.Secure the PCI-1710/1710HG by screwing the mounting bracket to the back panel of the computer.

7.Attach any accessories (68-pin cable, wiring terminal, etc.) to the card.

8.Replace the cover of your computer. Connect the cables you removed in step 2.

9.Turn the computer power on.

Chapter 2 Installation

11

Image 15

Contents PCI-1710/1710HG Multifunction DAS Card for PCI Bus Http/support.advantech.com Contents Appendix a 82C54 Counter Chip Functions General Information On-board Fifo First In First Out Memory Flexible Inputs Types and Ranges SettingIntroduction PCI-bus Plug and PlayOn-board Programmable Counter FeaturesAnalog Input SpecificationsLinearity error ±1 LSB Input impedance 1 GΩ Analog Output Digital InputDigital Output General Programmable Timer/Counter PCI Block DiagramInstallation Unpacking Initial InspectionInstallation Instructions Page Signal Connections I/O Connector OverviewPin Assignment I/O connector pin assignments for the PCI-1710/1710 HG card Input Connector Signal DescriptionsDigital Output signals Connector Signal Descriptions partSignal Reference Direction Description Name Single-ended Channel Connections Analog Input ConnectionsSingle-ended input channel connection Differential Channel ConnectionsAignd Differential input channel connection floating signal source 10V Analog Output ConnectionsTrigger Source Connections Internal Pacer Trigger ConnectionExternal Trigger Source Connection Field Wiring Considerations Page Register Structure and Format I/O Port Address Map Base Read DI9 DI8 DI7 DI6 DI5 DI4 DI3 DI2 DI1 DI0 Base Write DO9 DO8 DO7 DO6 DO5 DO4 DO3 DO2 DO1 DO0 Software A/D Trigger BASE+0 Channel Number and A/D Data BASE+0 and BASE+1A/D Channel Range Setting BASE+2 PCI-1710 PCI-1710HG MUX Control-BASE+4 and BASE+5 Example Control Register BASE+6 Status Register BASE+6 and BASE+7 Clear Interrupt and Fifo BASE+8 and BASE+9 11 D/A Output Channel 1 BASE+12 and BASE+13 10 D/A Output Channel 0 BASE+10 and BASE+1112 D/A Reference Control BASE+14 Read Digital Input Digital I/O Registers BASE+16 and BASE+17Calibration PCL-1710/1710HG VR assignment VR AssignmentFollowing list shows the function of each VR A/D CalibrationD/A Calibration Self A/D Calibration Page 82C54 Counter Chip Functions Intel 82C54 CounterCounter 1 Description Counter Read/Write Control RegistersRW1 & RW0 STA = Counter Operating Modes Mode 0 Stop on Terminal CountMode 1 Programmable One-shot Pulse Mode 2 Rate GeneratorMode 3 Square Wave Generator Mode 4 -Software-Triggered StrobeMode 5 Hardware-Triggered Strobe Counter Read-back Command Counter OperationsRead/Write Operation Counter Latch Operation