Accton Technology 1500 manual Return Process, North and South America

Page 89

EtherHub 1500 System User’s Guide

Return Process

Before you may return any Accton product to Accton, you must request an RMA number by calling, FAXing or writing Accton’s Service Department at the address listed below. If you ship the product, you must assume the risk of damage or loss in transit. You must use the original container (or the equivalent) and pay the shipping charge. Accton may replace or repair the product with either a new or reconditioned product, and the returned product becomes Accton’s property. At Accton’s sole discretion, Accton will issue a credit for either a comparable replacement Accton product or credit the original purchase price towards the purchase of any Accton product for any unrepairable, defective product.

This warranty does not cover replacement of products damaged by abuse, accident, misuse, neglect, alteration, repair, disaster, improper installation or improper testing.

ACCTON SHALL NOT BE HELD LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE, INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES CAUSED BY THE USE OF THIS PRODUCT OR INABILITY TO USE IT, EVEN IF THE COMPANY OR ACCTON HAS BEEN ADVISED OF SUCH LIABILITY OR OTHER SPECIAL CLAIMS.

If you purchased this product in the USA, be aware that some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights which vary from state to state. All parts or components contained in this product are covered by Accton’s Limited Lifetime Warranty for this product. The product may contain fully tested, recycled parts, warranted as if new.

For warranty information:

All territories except North and South America:

Accton Technology Corporation,

International Headquarters

No. 1, Creation Rd. III, Science-based Industrial Park, Hsinchu 300, Taiwan, R.O.C.

Phone: 886-35-770-270 Fax:

886-35-770-267 BBS: 886-35-770-654

North and South America:

Accton Technology Corporation,

USA Headquarters

 

1962 Zanker Road, San Jose, CA 95112, U.S.A.

 

Phone: 408-452-8900

Fax:

408-452-8988

BBS: 408-452-8828

Product Support Services

C-5

Image 89
Contents EtherHub 1500 System EtherHub 1500 System QWHUQDWLRQDO-HDGTXDUWHUV FCC Warning Sicherheitshinweise About this Guide Package Contents Contents Setup and Configuration Hardware InstallationApplications Appendix C Product Support Services Appendix a Product SpecificationsAppendix B Pin Assignments Glossary IndexList of Figures EtherHub 1500 System OverviewOverview Overview ∙ BNC EH1551, default module preinstalled in EH1500 Features of EtherHub 1500 SystemDistinguishing Factors of EtherHub 1500 System EtherHub 1500 System User’s Guide Front Panel Displays Chapter Hardware DescriptionSmartWatch LED Panel for EtherHub-16i+ SmartWatch LED PanelColor Green Label PWR/CPU Function Power indicator Terminator Snmp EtherHub 1500 System User’s Guide Jabber EtherHub 1500 System User’s Guide Alert Collision EtherHub 1500 System User’s Guide Segment LED Indicators EtherHub 1500 System User’s Guide Hub ID Indicators Partition Link PARTITION/DISABLED Configure Button STP Station Ports Daisy-Chain SwitchRear Panel Displays Socket SwitchBUS Power Switch Power SocketBefore You Begin Chapter Hardware InstallationHardware Installation Stacking Hubs without a Rack Stacking Hubs without a RackMounting Hubs on a Rack Mounting Hubs Using a Mounting RackConnecting the Hub System EtherHub 1500 System User’s Guide Connecting the Hub’s RS232 Serial Port to a PC COM Port Preparing for System ConfigurationEtherHub 1500 Site Running the Out-of-Band Configuration Program Installing an Snmp Backup Agent EtherHub 1500 System User’s Guide Diagnostic Tests Chapter Setup and ConfigurationSystem Setup Multi-Segment Architecture FlexBus 1500 Management Link Hub ID SettingSnmp Backup Agent Port Backup Function Hot Remove Function Preparing for Configuration ManagementFrom a local console ∙ Terminal Channel for local hookup Menu System Menu Trap Managers Download Restart Factory SettingsChanging System Configuration Downloading System Software Control Menu Hub Port Backup Port Push ButtonConfiguring Port Parameters Threshold Menu Performance MenuTo set thresholds Using the Configure Button To summarize Active LEDs Segment LEDs Attach the hub to one segment Master Agent Setting EtherHub-16mi+only Diagnostic function Attaching Stack to One Segment ApplicationsAttaching Hubs in Stack to 3 Segments Attaching Stack to Three SegmentsLinking Part of the Stacked Hubs to a Segment Attaching Stack to Multiple SegmentsStacked Hubs Not Linked to a Segment Each Hub is IsolatedExtending the Network with STP/BNC Connections Linking Stacked Hubs to a Network Management Station Linking a Stack to a Network Management StationLinking Segments in a Stacked System Interconnecting SegmentsLinking a Distributed Segment Linking a Distributed SegmentDistributed Multi-Segment Environment Linking Distributed SegmentsPhysical Characteristics Appendix a Product SpecificationsFeatures PVC Specifications for FlexBus 1500 CableNext for Horizontal FlexBus 1500 Cable Attenuation for Horzontal FlexBus 1500 CableUSA Standards ComplianceRS232 Port Pin Description Appendix B Pin AssignmentsFlexBus 1500 Pin Description DB9 Serial Port to RJ-45 Converter Connector Pin Assignment DB25 RS232 to RJ-45 Converter Connector Pin Assignment DCE Port Problem Report Appendix C Product Support ServicesHardware Repair Service Product RegistrationBulletin Board Service BBS Software Update and Upgrade ServiceTechnical Support Interactive Fast Fax U.S.A. officeCustomer Remedies Limited WarrantyNorth and South America Return ProcessOrdering Information 10BASE-T GlossaryLED Out-of-Band Index Index Index Troubleshooting EH1501s EH1502s E0895-R01