ADIC Scalar Series manual Rear Panel Switches and Connectors, Scsi I/O, AC Power, Power Switch

Page 32
Rear Panel Switches and Connectors

Rear Panel Switches and Connectors

Switches and connectors on the rear of the Scalar Library are shown below.

Drive

SCSI ID

Switches

Drive

SCSI I/O

Connectors

 

Serial Port

Library

Connector

SCSI I/O

 

Connectors

 

AC Power

 

Connector

 

Power Switch

 

 

Rear of adic Scalar 448

 

 

Rear Panel Switches and Connectors

 

 

Power Switch

Turns on AC power to the Scalar Library.

 

 

AC Power Connector

Plug the Scalar Library AC power cord into this connector.

 

 

SCSI I/O Connectors

Connections for the interface cable (s), SCSI jumpers, and/or SCSI

 

terminators, which are used to connect the Scalar Library to the host

 

computer SCSI bus(es) or to other devices on the SCSI channel.

 

 

Drive SCSI ID Rotary Switches

Sets the SCSI ID for each drive.

 

 

22

Equipment Description

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Scalar Series I n s t a l l a t i o n a n d O p e r a t i n g G u i d eCopyright Notice Copyright adicCopyright Notice Europe Copyright 1995 adic EuropeEMI/RFI Compliance United States - FCCCanada - Department of Communications Shielded CablesDECLARATION OF CONFORMITY according to ENBlank Page Table of Contents What Happens When Door is Opened viiiSafety Warnings RISK OF ELECTRIC SHOCK DO NOT OPENPrecautions This Chapter … ChapterThe Scalar Series The Scalar Features Scalar Series Models# Drives # Tape SlotsOptions DLT DrivesDifferential SCSI Maximum Capacity and Sustained Transfer RatesThe Scalar Blank Page Getting Started Unpacking and Inspecting Checking the AccessoriesRequirements Preparing the Library for Installation Prepare and Install the Data CartridgesWrite-Protect Switch Barcode LabelsInstall Data Cartridges Install Cleaning Cartridge OptionalClose and Lock the Front Door Figure 4. DLT Cartridge Write-Protect SwitchSetting the SCSI IDs Drive SCSI ID Rotary SwitchesPower Off the Computer Confirm and/or Install the SCSI Host InterfaceBackup Software Preparing the Host Computer SystemConnecting the Scalar Library steps you through the final phase of the installation processInstalling SCSI Cables, Jumpers, and Terminators Determining Your SCSI ConfigurationThe following table provides several examples of SCSI configurations Configuration LegendSCSI Configuration 1 - One SCSI Bus Connecting the ScalarSCSI Configuration 2 - Two SCSI Buses SCSI Configuration 3 - Three SCSI BusesSCSI Configuration 4 - Four SCSI Buses SCSI Configuration 5 - Five SCSI BusesPowering on the System Installing the Backup SoftwareEquipment Description Equipment Description Front Panel Switches and IndicatorsFront of adic Scalar Library when equipped with Mailbox Displays and Indicators Power LEDDisplay LOCKED LEDRear Panel Switches and Connectors Drive SCSI ID Switches Drive SCSI I/O ConnectorsAC Power ConnectorMedia Interchange Shelf Mailbox Off-Line Mode Menus MENU key Configuration MenuBuzzer Configuration Off-Line Time Set SCSI IDProduct Sign-On Initialize Map Slots Initialize Scan BarcodesDiagnostics Menu Barcode ScannerWrite Flash Memory Mode Serial Dnld Flash ModeBlank Page Operation and Maintenance describes normal operation features of the Scalar Libraryprovides details on the media and drive head cleaning cartridge explains normal maintenance proceduresPower Up Checks Normal OperationsGeneral Guidelines Opening the Front DoorResuming Operation Drive Power-on Self-TestWhat Happens When Door is Opened Drive Status Indicator Displays and ActionsDrive State The Tape in Use LED turns OFF. The Operate Handle LEDcontinued on next page Drive Operating ConditionsUse the following table to determine each drive’s operating condition Operation and Maintenance DLT Media DLT Data CartridgeUsing the Mailbox Scalar 458 only On-Line ModeLoading a Cartridge into Scalar 458 Library Unloading a Cartridge from Scalar 458 LibraryDiagnostic Menu Off-Line ModeLoading a Cartridge into Drive Unloading a Cartridge from Drive Moving a Cartridge to/from the Storage Shelves Normal Maintenance Cleaning the Drive HeadCleaning Tape Figure 16. DLT Cleaning TapeManually Inserting the Cleaning Tape Head Cleaning ProcedureCleaning Tape in Mailbox Scalar 458 only or Storage Slot Causes of the Use Cleaning Tape Warning Cleaning the Enclosure Operation and Maintenance Troubleshooting and Diagnostics includes information on error codes and the built-in diagnosticsInstallation Problems Library and Drive Operational ProblemsTroubleshooting and Diagnostics Library Error CodesEnvironmental Considerations When You Call adic Customer Assistance This Appendix … Diagnostics MenuAppendix Drive Type Diagnostics MenuError Counters Event CountersOperation Log Diagnostics MenuFirmware Revision Position Picker at Slot Press ENTER to select the Servo ControllerPosition Picker at Mbox when Mailbox equipped Position Picker at DrvPick From Drive Pick From Mailbox when Mailbox equippedPick From Slot Place In Drive Place In Mailbox when Mailbox equippedPlace In Slot Test Secondary Fan Map SlotsCalibrate X and Y Open Drive Door Close Drive DoorGlossary cartridge 62GlossarySCSI bus slotterminator unload64Glossary Specifications Power Consumption DriveLibrary ReliabilityError Codes Error Code Listing Scalar Series Error CodesError Codes CodeThe jaws do not move at all Error Codes Index 72Index Index73 74Index
Top Page Image Contents