ADIC Scalar Series Drive Power-on Self-Test, What Happens When Door is Opened, Resuming Operation

Page 43
What Happens When Door is Opened

What Happens When Door is Opened

Whenever you open the front door of the Scalar Library , the following actions occur:

The library will return Unit Attention and Not Ready status to the host computer.

Any function, if executed, that would change the state of the robotics machine is disabled.

Resuming Operation

To resume normal operation, close the door and lock it.

After the door is closed:

The library will perform its power up checks.

The application software may update its own cartridge inventory.

Drive Power-on Self-Test

When you power up your Scalar Library , the DLT drives each perform a Power-on Self-Test (POST) while the library is performing the Power Up Checks. The sequence of events for each drive is:

1.The LEDs on the right front panel of the drive will turn on sequentially from top to bottom. All LEDs will remain ON for a few seconds.

2.The LEDs on the left front panel of the drive will turn ON at the same time for about three seconds and then turn OFF.

3.The Operate Handle, Write Protected, and Use Cleaning Tape LEDs will turn OFF. The

Tape in Use LED will blink while the tape drive initializes.

If your external SCSI bus terminator has a Term Power LED it should also be illuminated.

Operation and Maintenance

33

Image 43
Contents I n s t a l l a t i o n a n d O p e r a t i n g G u i d e Scalar SeriesCopyright adic Copyright NoticeCopyright 1995 adic Europe Copyright Notice EuropeShielded Cables EMI/RFI ComplianceUnited States - FCC Canada - Department of Communicationsaccording to EN DECLARATION OF CONFORMITYBlank Page Table of Contents viii What Happens When Door is OpenedRISK OF ELECTRIC SHOCK DO NOT OPEN Safety WarningsPrecautions The Scalar Series ChapterThis Chapter … The Scalar # Tape Slots FeaturesScalar Series Models # DrivesMaximum Capacity and Sustained Transfer Rates OptionsDLT Drives Differential SCSIThe Scalar The Scalar Getting Started Requirements Checking the AccessoriesUnpacking and Inspecting Barcode Labels Preparing the Library for InstallationPrepare and Install the Data Cartridges Write-Protect SwitchFigure 4. DLT Cartridge Write-Protect Switch Install Data CartridgesInstall Cleaning Cartridge Optional Close and Lock the Front DoorDrive SCSI ID Rotary Switches Setting the SCSI IDsPreparing the Host Computer System Power Off the ComputerConfirm and/or Install the SCSI Host Interface Backup Softwaresteps you through the final phase of the installation process Connecting the Scalar LibraryDetermining Your SCSI Configuration Installing SCSI Cables, Jumpers, and TerminatorsConnecting the Scalar The following table provides several examples of SCSI configurationsConfiguration Legend SCSI Configuration 1 - One SCSI BusSCSI Configuration 3 - Three SCSI Buses SCSI Configuration 2 - Two SCSI BusesSCSI Configuration 5 - Five SCSI Buses SCSI Configuration 4 - Four SCSI BusesInstalling the Backup Software Powering on the SystemEquipment Description Front of adic Scalar Library when equipped with Mailbox Front Panel Switches and IndicatorsEquipment Description LOCKED LED Displays and IndicatorsPower LED DisplayConnector Rear Panel Switches and ConnectorsDrive SCSI ID Switches Drive SCSI I/O Connectors AC PowerMedia Interchange Shelf Mailbox Off-Line Mode Menus Buzzer Configuration Configuration MenuMENU key Product Sign-On Set SCSI IDOff-Line Time Initialize Scan Barcodes Initialize Map SlotsBarcode Scanner Diagnostics MenuSerial Dnld Flash Mode Write Flash Memory ModeEquipment Description explains normal maintenance procedures Operation and Maintenancedescribes normal operation features of the Scalar Library provides details on the media and drive head cleaning cartridgeOpening the Front Door Power Up ChecksNormal Operations General GuidelinesWhat Happens When Door is Opened Drive Power-on Self-TestResuming Operation The Tape in Use LED turns OFF. The Operate Handle LED Drive StatusIndicator Displays and Actions Drive StateUse the following table to determine each drive’s operating condition Drive Operating Conditionscontinued on next page Label DLT Data Cartridge DLT MediaUnloading a Cartridge from Scalar 458 Library Using the Mailbox Scalar 458 onlyOn-Line Mode Loading a Cartridge into Scalar 458 LibraryLoading a Cartridge into Drive Off-Line ModeDiagnostic Menu Unloading a Cartridge from Drive Moving a Cartridge to/from the Storage Shelves Figure 16. DLT Cleaning Tape Normal MaintenanceCleaning the Drive Head Cleaning TapeCleaning Tape in Mailbox Scalar 458 only or Storage Slot Head Cleaning ProcedureManually Inserting the Cleaning Tape Causes of the Use Cleaning Tape Warning Cleaning the Enclosure Blank Page includes information on error codes and the built-in diagnostics Troubleshooting and DiagnosticsLibrary and Drive Operational Problems Installation ProblemsEnvironmental Considerations Library Error CodesTroubleshooting and Diagnostics When You Call adic Customer Assistance Appendix Diagnostics MenuThis Appendix … Diagnostics Menu Drive TypeDiagnostics Menu Error CountersEvent Counters Operation LogFirmware Revision Press ENTER to select the Servo Controller Position Picker at SlotPosition Picker at Drv Position Picker at Mbox when Mailbox equippedPick From Slot Pick From Mailbox when Mailbox equippedPick From Drive Place In Slot Place In Mailbox when Mailbox equippedPlace In Drive Calibrate X and Y Map SlotsTest Secondary Fan Close Drive Door Open Drive DoorGlossary 62Glossary cartridgeunload SCSI busslot terminator64Glossary Specifications Reliability Power ConsumptionDrive LibraryError Codes Code Error Code ListingScalar Series Error Codes Error CodesThe jaws do not move at all Blank Page Index 72Index Index73 74Index