ADIC Scalar Series manual Using the Mailbox Scalar 458 only, On-Line Mode

Page 48
Using the Mailbox (Scalar 458 only)

Using the Mailbox (Scalar 458 only)

On-Line Mode

When the Scalar Library is in On-Line Mode the application software is in control and directs all library operations. The application software can use the Mailbox to insert or remove individual cartridges to/from the drives, or to/from the cartridge storage shelves. Follow closely the instructions the application software provides on your host computer system monitor.

The design of the Mailbox includes access control doors and cartridge stops in each of the media slots. The doors are unlocked, except when the library is performing a media transport operation (pick and place). The cartridge stops are solenoid controlled and prevent incorrect insertion of the media. The stops are held in the raised position whenever the Mailbox access doors are unlocked. During library pick and place operations the stops are lowered, allowing the library to insert or remove cartridges from the slots using the Media Picker.

Warning

The Mailbox access control doors are locked when the application software performs a media transport operation (pick and place), or, the application can lock the access control doors at any time. You cannot open either door during this operation without severely damaging the Scalar 458. Wait until your application software instructs you to open either of these doors.

Loading a Cartridge into Scalar 458 Library

Open the appropriate Mailbox access control door as instructed.

Place the cartridge into the appropriate slot of the Mailbox with the write-protect switch at the top and the barcode label facing you. Slide the cartridge in until the stop will not allow it to go any farther.

Note

The cartridge is inserted with the write-protect switch at the top and the barcode label facing you. However, the cartridge stops will prevent you from installing the media incorrectly.

Close the Mailbox access control door.

Follow any additional instructions provided by the application software.

The application software will now perform the intended operation with the cartridge.

Unloading a Cartridge from Scalar 458 Library

The application software will cause the cartridge to be ejected from the drive and will issue the pick and place commands to have the library move the cartridge to a Mailbox slot.

Open the appropriate access control door and remove the cartridge from the Mailbox.

Close the access control door.

38

Operation and Maintenance

Image 48
Contents Scalar Series I n s t a l l a t i o n a n d O p e r a t i n g G u i d eCopyright Notice Copyright adicCopyright Notice Europe Copyright 1995 adic EuropeEMI/RFI Compliance United States - FCCCanada - Department of Communications Shielded CablesDECLARATION OF CONFORMITY according to ENBlank Page Table of Contents What Happens When Door is Opened viiiSafety Warnings RISK OF ELECTRIC SHOCK DO NOT OPENPrecautions Chapter The Scalar SeriesThis Chapter … The Scalar Features Scalar Series Models# Drives # Tape SlotsOptions DLT DrivesDifferential SCSI Maximum Capacity and Sustained Transfer RatesThe Scalar Blank Page Getting Started Checking the Accessories RequirementsUnpacking and Inspecting Preparing the Library for Installation Prepare and Install the Data CartridgesWrite-Protect Switch Barcode LabelsInstall Data Cartridges Install Cleaning Cartridge OptionalClose and Lock the Front Door Figure 4. DLT Cartridge Write-Protect SwitchSetting the SCSI IDs Drive SCSI ID Rotary SwitchesPower Off the Computer Confirm and/or Install the SCSI Host InterfaceBackup Software Preparing the Host Computer SystemConnecting the Scalar Library steps you through the final phase of the installation processInstalling SCSI Cables, Jumpers, and Terminators Determining Your SCSI ConfigurationThe following table provides several examples of SCSI configurations Configuration LegendSCSI Configuration 1 - One SCSI Bus Connecting the ScalarSCSI Configuration 2 - Two SCSI Buses SCSI Configuration 3 - Three SCSI BusesSCSI Configuration 4 - Four SCSI Buses SCSI Configuration 5 - Five SCSI BusesPowering on the System Installing the Backup SoftwareEquipment Description Front Panel Switches and Indicators Front of adic Scalar Library when equipped with MailboxEquipment Description Displays and Indicators Power LEDDisplay LOCKED LEDRear Panel Switches and Connectors Drive SCSI ID Switches Drive SCSI I/O ConnectorsAC Power ConnectorMedia Interchange Shelf Mailbox Off-Line Mode Menus Configuration Menu Buzzer ConfigurationMENU key Set SCSI ID Product Sign-OnOff-Line Time Initialize Map Slots Initialize Scan BarcodesDiagnostics Menu Barcode ScannerWrite Flash Memory Mode Serial Dnld Flash ModeBlank Page Operation and Maintenance describes normal operation features of the Scalar Libraryprovides details on the media and drive head cleaning cartridge explains normal maintenance proceduresPower Up Checks Normal OperationsGeneral Guidelines Opening the Front DoorDrive Power-on Self-Test What Happens When Door is OpenedResuming Operation Drive Status Indicator Displays and ActionsDrive State The Tape in Use LED turns OFF. The Operate Handle LEDDrive Operating Conditions Use the following table to determine each drive’s operating conditioncontinued on next page Operation and Maintenance DLT Media DLT Data CartridgeUsing the Mailbox Scalar 458 only On-Line ModeLoading a Cartridge into Scalar 458 Library Unloading a Cartridge from Scalar 458 LibraryOff-Line Mode Loading a Cartridge into DriveDiagnostic Menu Unloading a Cartridge from Drive Moving a Cartridge to/from the Storage Shelves Normal Maintenance Cleaning the Drive HeadCleaning Tape Figure 16. DLT Cleaning TapeHead Cleaning Procedure Cleaning Tape in Mailbox Scalar 458 only or Storage SlotManually Inserting the Cleaning Tape Causes of the Use Cleaning Tape Warning Cleaning the Enclosure Operation and Maintenance Troubleshooting and Diagnostics includes information on error codes and the built-in diagnosticsInstallation Problems Library and Drive Operational ProblemsLibrary Error Codes Environmental ConsiderationsTroubleshooting and Diagnostics When You Call adic Customer Assistance Diagnostics Menu AppendixThis Appendix … Drive Type Diagnostics MenuError Counters Event CountersOperation Log Diagnostics MenuFirmware Revision Position Picker at Slot Press ENTER to select the Servo ControllerPosition Picker at Mbox when Mailbox equipped Position Picker at DrvPick From Mailbox when Mailbox equipped Pick From SlotPick From Drive Place In Mailbox when Mailbox equipped Place In SlotPlace In Drive Map Slots Calibrate X and YTest Secondary Fan Open Drive Door Close Drive DoorGlossary cartridge 62GlossarySCSI bus slotterminator unload64Glossary Specifications Power Consumption DriveLibrary ReliabilityError Codes Error Code Listing Scalar Series Error CodesError Codes CodeThe jaws do not move at all Error Codes Index 72Index Index73 74Index