PC Concepts ADSL2+ user manual 2 RIP, Rip

Page 76

The NAT Global Information table, which displays the following settings that apply to all NAT rule translations:

zTCP Idle Timeout (sec), TCP Close Wait (sec), TCP Def Timeout (sec): When two computers communicate via the Internet, a Transmission Control Protocol-based communication session is created between them to control the exchange of data packets. The TCP session can be viewed as being in one of three states, depending on the types of packets being transferred: the establishing state, where the connection is being set up, the active state, where the connection is being used to transfer data, and the closing state, in which the connection is being shut down. When a NAT rule is in effect on a TCP session in the active state, the session will timeout if no packets are received for the time specified in TCP Idle Timeout. When in the closing state, the session will timeout if no packets are received for the time specified in TCP Close Wait. When in the establishing state, the session will timeout if no packets are received for the time specified in TCP Def Timeout.

zUDP Timeout (sec): Same as TCP Idle Timeout, but for User Datagram Protocol-based communication sessions.

zICMP Timeout (sec): Same as TCP Idle Timeout, but for Internet Control Message Protocol-based communication sessions.

zGRE Timeout (sec): Same as TCP Idle Timeout, but for Generic Routing Encapsulation-based communication sessions.

zESP Timeout (sec): Same as TCP Idle Timeout, but for Encapsulating Security Payload-based communication sessions.

zDefault Nat Age (sec): For all other NAT translation sessions, the number of seconds for which a NAT translation will continue to be valid if no packets are received.

zNAPT Port Start/End: When an napt rule is defined, the source ports will be translated to sequential numbers in this range

5.7.2RIP

Your ADSL/Ethernet router can be configured to communicate with other routing devices to determine the best path for sending data to its intended destination. Routing devices communicate this information using a variety of IP protocols. This topic describes how to configure your [Productname] to use one of these, called the Routing Information Protocol

(RIP).

75

Image 76
Contents ADSL2+ Copyright Contents Admin 100 Backup/Restore Configuration102 System Requirements Package ContentsAdsl Compliant ATM Protocols and Encapsulations PPP SupportBridging/Routing Support IP ManagementDevice management InterfaceFront Panel Indicators and Description Single-Port Adsl RouterDescriptions of LED status Four-Port Adsl RouterBack Panel Descriptions of All ConnectorsConnect Related Devices Page Setup Adsl router via Ethernet Cable Setup Adsl router via USB CablePage Page Page TCP/IP Configuration For Windows XPDouble-ClickNetwork Connections icon Page Page For Windows Select Internet Protocol TCP/IP then click Properties Page Page Select Gateway tab and click OK Option2 Configure IP Manually Page Setup Adsl Router via USB Cable on MAC Page Page Page Page Page Setup Adsl Router via USB Cable on Linux Compiling the DriverLogin LAN ConfigurationHome HomePage System Mode Quick Configuration Page LAN Configuration LANPage Dhcp Mode Dhcp Server Adding Dhcp Server Address PoolsDhcp Relay Follow these instructions to configure Dhcp relay Page WAN 1 DSLATM VC 3 PPP PPP Configuration table displays the following fields 4 EDA Page Ipoa Bridging BridgingEnabling Bridging Services ConfigurationWAN to WAN Bridging Enable/Disable Enabling Bridgeable InterfacesPage 3 DSL Page Page ATM VC Page RFC 1483 Interface EoA Routing IP RoutePage IP Address Table Page 4 DSL ATM VC Page 6 PPP Page 7 EOA Ipoa Page Services 1 NAT2 RIP RIPPage Select a metric value for the interface Select a Send Mode and a Receive ModeFirewall Page IP Filter Page Bridge Filter 6 DNS Blocked Protocols Page Ddns UPnP SntpAdmin User ConfigurationCommit & Reboot Local Image Upgrade Committing ChangesPage Remote Image Upgrade Image Upgrade Successful AlarmDiagnostics Click Submit Port Settings System LogBackup/Restore Configuration Page Management Control Configuring Autodetect Configuring the ATM Virtual Circuit Autodetect ModesAutodetect Snmp Configuration Creating Communities Click Add CommViewing Hosts Viewing Global Snmp StatisticsParental Control 103