3Com Hub 1000 SX manual Logging On, message, return the hub to the supplier

Page 38

message, return the hub to the supplier.

A-4APPENDIX A: USING THE CONSOLE PORT

	Hardware Version 0
	Bootcode Version		1.00, 02/05/98
	Firmware Version		1.00, 02/05/98
	****************************************************
	*			*
	*		SuperStack II (tm)	*
	*		Hub 1000 SX	*
	*	Copyright (c)1997 3Com Corporation		*
	*			*
	****************************************************
	Enter password ->
	Any POST FAIL message indicates a fatal hardware error. If you see a FAIL
	message, return the hub to the supplier.

Logging On	The default password that is set at the factory is admin. If this is the ﬁrst

time that anyone has logged on to the hub, enter the default password at the prompt:

admin

Asterisks (*) instead of plain text appear at the prompt while you are typing the password.

The Hub 1000 SX Conﬁguration menu appears.

***************************************************

**Hub 1000 Configuration Menu **

***************************************************

[1]Configure port settings

[2]Display hub status

[3]Update firmware image

[4]Change password

[5]Logout

Enter choice ->

To select an option from the Conﬁguration menu, enter the option number at the prompt.

After 4 minutes of inactivity, the CLI logs off automatically.

Image 38

Contents A member of the 3Com SuperStack II System SuperStack II Hub 1000 SXUser Guide 3Com Corporation 5400 Bayfront Plaza Santa Clara, California UNITED STATES GOVERNMENT LEGENDSABOUT THIS GUIDE 1 INTRODUCTION CONTENTS2 INSTALLING THE HUB POST Messages A USING THE CONSOLE PORT3 MAKING CONNECTIONS TECHNICAL SUPPORT SPECIFICATIONSGLOSSARY INDEX 3COM CORPORATION LIMITED WARRANTY FCC CLASS A VERIFICATION STATEMENTPage FIGURES Page TABLES Port Conﬁguration MenuPage Notice Type ABOUT THIS GUIDEIcon DescriptionMenu commands CommandsSETDEFAULT !0 -IP NETaddr = and buttonsGeneral Description INTRODUCTIONHub 1000 SX Full-Duplex Downlinksand Uplink OperationFlow Control Features and FunctionsINSTALLING THE HUB SuperStack II Hub 1000 SX User GuideHub Description The hub’s front and rear panels are shown in Figure Installing and Connecting the Hub4 Repeat steps 2 and 3 for the other side of the hub Maximum Cable ConnectorTable 2-1 Downlink Connections TypeColor Table 2-2 Hub 1000 SX IndicatorsIndicator StatusThe gigabit interface connector GBIC port on the rear panel of the Connecting aGBIC Module Using Optional Power SystemsPower Modules Cabling OptionsA hub connects to a UPS unit through the hub’s AC power cord Table 2-4 Advanced RPS Conﬁguration OptionsYou can connect a UPS unit to an Advanced RPS unit as long as you do not exceed the maximum wattage 325 watts for the UPS unit. To verify that the UPS unit’s maximum wattage is not exceeded, calculate the total power consumption of all units connected to the Advanced RPS. If the result is less than 325 watts, your conﬁguration is safe if the result is greater than 325 watts, then there are too many units connected to the Advanced RPS Page MAKING CONNECTIONS Table 3-1 Gigabit Ethernet Maximum Cable LengthsServers Power WorkgroupAggregating connecting to the network backbone. See FigureYou can use the Hub 1000 SX downlinks to aggregate 10/100 Mbps SwitchesThe Hub 1000 SX does not support bandwidth aggregation trunking Figure 3-3 Aggregated Switches Connection 3-4 CHAPTER 3 MAKING CONNECTIONSThe best use of the hub uplink is as a backbone connection to a 3Com ConnectingFigure 3-4 Mixed Connection Symptom Figure 3-6 Uplink Connection to a 10/100 Mbps SwitchTable 3-2 Troubleshooting Tips Solution USING THE CONSOLE PORT Requirements Connecting theWith Power Console PortConnecting the Console Port A-3 from powerTo connect the console port when the hub is disconnected DisconnectedAfter 4 minutes of inactivity, the CLI logs off automatically Logging Onmessage, return the hub to the supplier Changing the PasswordPort Settings ConﬁguringTo display the Port Conﬁguration menu Configuring Port Settings Table A-2 Port Conﬁguration MenuA-8 APPENDIX A USING THE CONSOLE PORT Configuring Port Settings and be conﬁgured to receive pause frames Configuring Port Settings A-11 matrix, Y indicates yes and n indicates no. See Table A-3 DisplayingHub Status Table A-3 Hub Status InformationDisplaying Hub Status A-13 Restoring the Factory Default Settings A-14 APPENDIX A USING THE CONSOLE PORTentering option Updating theFirmware Image Checking theXmodem-CRC To transfer the ﬁrmware image ﬁle log in again. To restart the ﬁle transfer, repeat steps 6 and during a ﬁrmware update, the CLI displays the following messageLogging Off While saving port settings or Table A-4 File Transfer Error MessagesTable A-5 Fatal Error Messages Environmental Operating Ranges SPECIFICATIONSPhysical Dimensions Page TECHNICAL SUPPORT ServicesBoard Service Online Technical1 408 654 Access by Analog ModemAccess by Digital Modem C-2 APPENDIX C TECHNICAL SUPPORTLocal access numbers are available within the following countries Central European HQ Santa Clara, CaliforniaCzech Republic/Slovak 305 261 3266 Miami, FloridaTo obtain an RMA number, call or fax Page GLOSSARY access method Carrier Sense Multiple Access/Collision Detection. Channel accesscable is based on CSMA/CD Carrier Sense Multiple Access/Collision transmission of light signalsﬂow control IEEEincoming Mbpscontrol. See also asymmetric ﬂow control, ﬂow control, pause frame Numbers SymbolsINDEX Page Switch 9300 3-2, 3-3 Page HARDWARE 3Com Corporation LIMITED WARRANTYSTANDARD WARRANTY SERVICE SOFTWAREGOVERNING LAW FCC CLASS A VERIFICATION STATEMENTLIMITATION OF LIABILITY