3Com Hub 1000 SX manual Table A-2 Port Conﬁguration Menu, Configuring Port Settings

Page 41

Configuring Port Settings

Configuring Port Settings

A-7

Table A-2Port Conﬁguration Menu

Option		Description

(1)	Enable port	Enable the port for linking. The factory
		default is all ports enabled.
(2)	Disable port	Disable the port for linking.
(3)	Enable auto-negotiation	Enable auto-negotiation. The factory
		default is auto-negotiation enabled on
		all ports.
(4)	Disable auto-negotiation (force link)	Disable auto-negotiation.
(5)	Show port settings	List the current settings for all ports.
(6)	Use factory default settings	Return selected ports to factory
		default settings.
(7)	Save new port settings	Save the settings. Select this option if you
		want settings to persist after a hub reset.
(8)	Exit without change to settings	Exit to the Hub 1000 SX Configuration
		menu without applying or saving settings.
(9)	Apply changes and exit	Apply the settings and exit to the
		Hub 1000 SX Configuration menu.

If you want settings to persist after a hub reset, you must select option 7 before selecting option 9.

Disabling Ports The following example shows how to disable ports 3, 5, 6, and 7 and apply the changes.

***************************************************

**Hub 1000 Configuration Menu **

***************************************************

[1]Configure port settings

[2]Display hub status

[3]Update firmware image

[4]Change password

[5]Logout

Enter choice -> 1

Enter port number(s), from 1 to 9: 3 5-7

****

Port Configuration Menu

****

(1)Enable port

(2)Disable port

(3)Enable Auto-Negotiation

(4)Disable Auto-Negotiation (Force link)

Image 41

Contents A member of the 3Com SuperStack II System SuperStack II Hub 1000 SXUser Guide UNITED STATES GOVERNMENT LEGENDS 3Com Corporation 5400 Bayfront Plaza Santa Clara, CaliforniaABOUT THIS GUIDE 1 INTRODUCTION CONTENTS2 INSTALLING THE HUB POST Messages A USING THE CONSOLE PORT3 MAKING CONNECTIONS GLOSSARY INDEX 3COM CORPORATION LIMITED WARRANTY SPECIFICATIONSTECHNICAL SUPPORT FCC CLASS A VERIFICATION STATEMENTPage FIGURES Page Port Conﬁguration Menu TABLESPage Icon ABOUT THIS GUIDENotice Type DescriptionSETDEFAULT !0 -IP NETaddr = CommandsMenu commands and buttonsGeneral Description INTRODUCTIONHub 1000 SX and Uplink DownlinksFull-Duplex OperationFlow Control Functions Features andSuperStack II Hub 1000 SX User Guide INSTALLING THE HUBHub Description The hub’s front and rear panels are shown in Figure Connecting the Hub Installing and4 Repeat steps 2 and 3 for the other side of the hub Table 2-1 Downlink Connections ConnectorMaximum Cable TypeIndicator Table 2-2 Hub 1000 SX IndicatorsColor StatusThe gigabit interface connector GBIC port on the rear panel of the Connecting aGBIC Module Power Systems Using OptionalCabling Options Power ModulesTable 2-4 Advanced RPS Conﬁguration Options A hub connects to a UPS unit through the hub’s AC power cordYou can connect a UPS unit to an Advanced RPS unit as long as you do not exceed the maximum wattage 325 watts for the UPS unit. To verify that the UPS unit’s maximum wattage is not exceeded, calculate the total power consumption of all units connected to the Advanced RPS. If the result is less than 325 watts, your conﬁguration is safe if the result is greater than 325 watts, then there are too many units connected to the Advanced RPS Page Table 3-1 Gigabit Ethernet Maximum Cable Lengths MAKING CONNECTIONSAggregating Power WorkgroupServers connecting to the network backbone. See FigureYou can use the Hub 1000 SX downlinks to aggregate 10/100 Mbps SwitchesThe Hub 1000 SX does not support bandwidth aggregation trunking 3-4 CHAPTER 3 MAKING CONNECTIONS Figure 3-3 Aggregated Switches ConnectionThe best use of the hub uplink is as a backbone connection to a 3Com ConnectingFigure 3-4 Mixed Connection Table 3-2 Troubleshooting Tips Figure 3-6 Uplink Connection to a 10/100 Mbps SwitchSymptom SolutionUSING THE CONSOLE PORT With Power Connecting theRequirements Console PortTo connect the console port when the hub is disconnected from powerConnecting the Console Port A-3 DisconnectedAfter 4 minutes of inactivity, the CLI logs off automatically Logging Onmessage, return the hub to the supplier Port Settings PasswordChanging the ConﬁguringTo display the Port Conﬁguration menu Table A-2 Port Conﬁguration Menu Configuring Port SettingsA-8 APPENDIX A USING THE CONSOLE PORT Configuring Port Settings and be conﬁgured to receive pause frames Configuring Port Settings A-11 Hub Status Displayingmatrix, Y indicates yes and n indicates no. See Table A-3 Table A-3 Hub Status InformationDisplaying Hub Status A-13 A-14 APPENDIX A USING THE CONSOLE PORT Restoring the Factory Default SettingsFirmware Image Updating theentering option Checking theXmodem-CRC To transfer the ﬁrmware image ﬁle log in again. To restart the ﬁle transfer, repeat steps 6 and during a ﬁrmware update, the CLI displays the following messageLogging Off While saving port settings or Table A-4 File Transfer Error MessagesTable A-5 Fatal Error Messages Environmental Operating Ranges SPECIFICATIONSPhysical Dimensions Page Board Service ServicesTECHNICAL SUPPORT Online TechnicalAccess by Digital Modem Access by Analog Modem1 408 654 C-2 APPENDIX C TECHNICAL SUPPORTLocal access numbers are available within the following countries Czech Republic/Slovak Santa Clara, CaliforniaCentral European HQ 305 261 3266 Miami, FloridaTo obtain an RMA number, call or fax Page GLOSSARY cable is based on CSMA/CD Carrier Sense Multiple Access/Collision Carrier Sense Multiple Access/Collision Detection. Channel accessaccess method transmission of light signalsincoming IEEEﬂow control Mbpscontrol. See also asymmetric ﬂow control, ﬂow control, pause frame Numbers SymbolsINDEX Page Switch 9300 3-2, 3-3 Page STANDARD WARRANTY SERVICE 3Com Corporation LIMITED WARRANTYHARDWARE SOFTWAREGOVERNING LAW FCC CLASS A VERIFICATION STATEMENTLIMITATION OF LIABILITY